Hello Guest it is March 29, 2024, 06:45:18 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Mavirick

Pages: 1 2 »
1
General Mach Discussion / Coordinates
« on: October 05, 2017, 10:40:36 AM »
Hi all

WOW thats allot of info

Thax

Sent from my SM-G900H using Tapatalk

2
General Mach Discussion / Coordinates
« on: October 04, 2017, 01:10:24 AM »
Hi Joe

No home switches mate only estops on one end of each axis

What is the beat way to set boundries and soft limits them

Thax Mav

Sent from my SM-G900H using Tapatalk

3
General Mach Discussion / Coordinates
« on: October 03, 2017, 11:18:57 AM »
Please could someone assist me with setting up my machine and job coordinates... everytime i run a wizard in mach3 it runs into a endstop before it gets to the job toolpath

Thanx
MAV

Sent from my SM-G900H using Tapatalk

4
General Mach Discussion /
« on: September 22, 2017, 11:05:01 AM »
And i have a manual for the controller

Sent from my SM-G900H using Tapatalk

5
General Mach Discussion /
« on: September 22, 2017, 11:03:38 AM »
Mate i never had it on machforwin64 thats how it can up originally on the first no device there was a pci-port only half of my msg was sent earlier ... for some reason when i went to devive set this is what came on what is strange is my mill is still running when i clesed this window somewhere over the weekend ill strip the pci card out take pics and reload windows 10 pro 64bit my hdd is fd up do im replacing it with a ssd then ill document the whole prosess ... if that will please the court..ill take screen shots as i go and if it was a fluke so be it if it wasnt ill figure it out and hopefully be able to help some blokes out

Cheers
MAV

Sent from my SM-G900H using Tapatalk

6
General Mach Discussion / Interference with axis motors
« on: September 22, 2017, 07:05:30 AM »
Thats what its aking after device setup


Sent from my SM-G900H using Tapatalk

7
General Mach Discussion / Interference with axis motors
« on: September 22, 2017, 03:41:07 AM »
Jip luckly it was just my workshop at home but its up your advice worked like a charm

And as promised 

I installed it on another pc and it also works I5 8gm ram and win 10 pro 64bit

Sent from my SM-G900H using Tapatalk

8
General Mach Discussion /
« on: September 21, 2017, 07:01:14 AM »
Hi craig

Thats perfect explanation thanx

The contractors assured me they will be done today... but as we know contractors arent always relaible they were suppose to finish on monday already.

I hop they will be done by the time i get home so i can test all these theories i have bought brand ne shielded cables and a lot of bits so hopefully i van sort this all out tonight

Sent from my SM-G900H using Tapatalk

9
General Mach Discussion /
« on: September 20, 2017, 02:33:05 PM »
Can someone please explain debounce in Mach3 what exactly does it do

Sent from my SM-G900H using Tapatalk

10
General Mach Discussion /
« on: September 20, 2017, 02:29:52 PM »
Hi Rich

Thanx for the info im sure ill find the problem

Craig i havnt forgotten to take the photos they are replacing the powe cables to my workshop at the moment so there is no power. According to the contractors they should be done bu lunchtime tomorrow then hopefully i can get everything on again to take the phots for you.

Ill update you if i get the problem fixed

Thanx for all the help sofar

Mav

Sent from my SM-G900H using Tapatalk

Pages: 1 2 »