Hello Guest it is March 28, 2024, 04:18:23 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bennet

Pages: 1 2 »
1
hello Tweakie , your help is gold...   I have understand how to pilot the Rc motor, and I wil try now.. But a little bit dubt, where i need  wire the two cables "signal from Mach3" on  interface board  to my breakborad terminals output: 


2
no, and never used it. I need buy it ?

3
can you send me a little schematic draw of your idea, then I will try this .  I'm sorry I have a study of base of the English language :-[

4
If you really want to control the motor from the motion controller, you could take the 0-10v output spindle speed control signal (if it has that), put it through a voltage devider ckt and send 0-5v to an analog input of the Arduino, then generate the pwm based on that. Easy to do the control, but why would you want to?
Go nuts man.

thanks Roaster for your reply detailed,  I have begun a project for conversion mini mill,and had already replace the spindle and motor original with a brushless motor, spindle ER11  and pulley with belt. Then I have a cnc system with four motor stepper Nema23, breakboard card ST-V2 and I need of drive the brushless motor.
Now you can explain in detailed info, also scheme draw it's a good,  how to wire from my terminals 0-10V pvm on breakboard with the voltage devider to motor brushless ?
I give to power the ESC controller a power supply PSU 12V. 30A, it's work fine 

5
I want use as spindle motor in mini mill, not same stepper motor. I want pilot the brushless with the card ST-V2 5 axis and mach3. But I not know how to make . I can wire the ESC control speed to output control spindle joint inverter on the breakboard ?

I have the BRUSHLESS :
Specs.
Turns: 10T
Voltage: 3~4S Lipoly
RPM/V: 1250kv
Internal resistance: 0.022Ohm
Max Loading: 54A
Max Power: 755W .

CONTROL SPEED SBEC Specs:
Max Cont. Current: 70A
Max Burst Current: 85A
Max BEC Current: 3A
BEC Voltage: 5.5v
LiPo: 2~6S
NiMH: 5~16cells
Weight: 84grams
Max RPM (2-pole): 200,000rpm
Size: 69 x 33 x 23mm
Motor Plug: Female 4mm bullet Connection
Battery Plug: Nil
Features.
Extremely low internal resistance
Very low operation temperature
Over temperature protection
APEC MoSfets (Taiwain)
Programming Options.
Battery Type: 2S~6S
Forward/Reverse
Soft Start
LV Cut off Type (Ignore, Reduce Power, Stop Motor)
LV Cut off setting (2.5~3.5v in 0.1v increments)
Timing (Auto, Very Low, Low, Normal, High, Very Hgh)
Switching (8,16kHz)
Factory Restore
Active RPM Control: On/Off (Governor Mode)
Default factory settings.
Brake: off
Battery: LiPo Auto Detect
Low Voltage: 3.2v (power down motor)
Timing: Auto
Frequency: 8KHz

SERVO TESTER  :
Servo & CCPM Servo Consistency Master/Checker
Size: 49x43x29mm
Input: 4.8 ~ 6V
Output up to 3 servos at once!

And the breakboard is this :

6
can you explain me how to make ? I have also the servo tester for variable speed motor.

the follow picture this is the the wiring scheme for right use of motor and the output /input wires of the control speed driver.

the red wire send 5V for power the servo tester, and the yellow wire is a signal, green wire is the ground.
 

7
hi, I need know if possible pilot the motor brushless with  5 axis stepper motor card :

8
Tweakie my major difficulty is for setting Mach3 only for a basic test of drivers and motors wired same in picture attached..
Also I not know a basic configuration commands to insert in the menus setup.
I never had experience about cnc software setup.. Possible for you place here a little example to begin ?
You can see the my last picture attached ? You think that the hardware is wired right ?

9
hi Tweakie,

I have wired both cards, power both with +5V and intalled Mach3 and the plugin . The uc300eth is detected fine. Now I not know how to test all my config hardware.
I need of full configuration of Mach3 for try the motors and drivers. Can you help me ?

10
ok, I try , I have also add 3 driver and linked 2 power supply for each card , it's ok ? Also ETH port and usb together linked to Pc ?


Pages: 1 2 »