Hello Guest it is November 27, 2022, 07:04:10 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Nleo22

Pages: 1 2 »
1
Mach4 General Discussion / Re: Help mazh4 z-axis act-up
« on: August 21, 2022, 05:34:06 PM »
I recheck the step driver and I saw idle percent at 80%. I change it down to 40% for z-axis. Jogging for 20mins seems up&down normal now. Why is that🤔

2
Mach4 General Discussion / Re: Help mazh4 z-axis act-up
« on: August 21, 2022, 05:31:14 PM »
Not sure step lose. Sometimes I let machine sitting for awhile, come back jogging z-axis up&down it only move 1direction down. Then restart machine. It went back to normal.

3
Mach4 General Discussion / Re: Help mazh4 z-axis act-up
« on: August 21, 2022, 07:52:06 AM »
Yes I ref home all axis

4
Mach4 General Discussion / Re: Help mazh4 z-axis act-up
« on: August 20, 2022, 10:34:16 PM »
Richard Gonzalez all wired correctly and it moving correctly up and down direction. Here is the problem It act up when I jogging fast up&down for over 3 minutes then it only move down even I scroll up and down again only move down...

5
Mach4 General Discussion / Help mazh4 z-axis act-up
« on: August 20, 2022, 08:33:09 PM »
Help mach4 z-axis direction are correct up&down but then after jogging non-stop up&down for 3-5mins, it start moving down only even I scroll up.... doesn't any body have this problem 😕 🤔.
I have to restart mach4 the it back to normal but then again jogging non-stop it start to act up.

6
Help, mach3 or mach4 I Looking for 5axis post process for mastercam or solidwork.

7
Few people have created topic similar but different or wrong model. I'm posting the right one right model and guide y'all Thu this.
This for model XHC WHB04B-6 axis or WHB04B-4 axis enable plugin setup

I'm using "INCHES" and I CAN MOVE steps 0.001", 0.010", 0.100", 1.00" etcs...
WHB04B-6 axis with Mach4 also work for 4axis as well.

Video to guide yall
https://www.youtube.com/watch?v=Gl-XXBQ_T8M

make sure select MPG #1 and Macro 10= select function "Machine Enable"
Let me know it working for you. look forward to your answer.

Mach4 lastest version can be found under this link.
http://www.machsupport.com/ftp/Mach4/DevlopmentVersions/

Download version Mach4Hobby_Installer-4.2.0.4839
http://www.machsupport.com/ftp/Mach4/DevlopmentVersions/Mach4Hobby_Installer-4.2.0.4839.exe

8
Mach4 Plugins / Re: XHC WB04 plugin
« on: April 30, 2022, 10:01:18 AM »
I try rushing to the video haven't show yall steps.
Here I redo my video and its longer =D, here NEW VIDEO JUST UPLOADED. I'M USING INCHES I CAN MOVE 0.001", 0.010", 0.100", 1.00" etcs...
https://www.youtube.com/watch?v=Gl-XXBQ_T8M


make sure select MPG #1 and Macro 10= select function "Machine Enable"

Let me know it working for you. look forward to your answer.

9
Mach4 Plugins / Re: XHC WB04 plugin
« on: April 26, 2022, 09:36:28 PM »
Hey all, I'm using the plugins copied from the development version in to 4612, seems to work great apart from the step/cont jog
- For versions up to 4746 i have repeatable steps but not continuous mode
- For versions after that up to 4839 i have continuous at all speeds but no steps

Just wanted to confirm if that's what others are experiencing at this stage or if there is a solution to this

https://www.youtube.com/watch?v=3lp7KtA_5uM&t=262s

Watch my YouTube video, and I'm using mach4 version 4.2.0.4839, with whb04b-6 video proof that it working. Also make sure you don't select MPG # 0, because it not work. You have to select MPG #1 and above then your axis's steps travel will work. Go over my video.

10
Mach4 Plugins / Re: XHC WB04 plugin
« on: April 25, 2022, 11:57:43 AM »
https://www.youtube.com/watch?v=3lp7KtA_5uM&t=262s

Showing yall the setup, Watch my video also work for lastest mach4 version 4.2.0.4839

Pages: 1 2 »