Messages

1

General Mach Discussion / Re: HELP!!! ASAP!!! TIA!!! Tool display image

« on: May 08, 2017, 04:18:57 PM »

And yes I do have valid licenses for both mach3 and lazycam. Like I said it before I didn't have this issue. Until now

2

General Mach Discussion / Re: HELP!!! ASAP!!! TIA!!! Tool display image

« on: May 08, 2017, 04:18:16 PM »

Reinstalled and still does the same thing... old gcode work fine. The ones before the power went out. I try to load new ones and they don't seem to display the image. . . For the new ones it says Nested Comment found Block = N5 .

3

General Mach Discussion / Mach3 not displaying Gcode anymore

« on: May 05, 2017, 10:51:57 PM »

Let me clear things up a bit... I had a power outage while working with mach3. Before the power outage mach3 would display the gcode with no problems in the table display box. But after the power outage mach3 does not display the gcode in the display box. Only in the gcode list(left side). I have cut several pieces before and had it running with no problem. Please help me if anybody knows. Thanks in advance guys

4

General Mach Discussion / HELP!!! ASAP!!! TIA!!! Tool display image

« on: May 05, 2017, 07:51:33 PM »

Good afternoon, I ran into an issue just now. Ok so I turned on the cnc machine and my rig up and they booted up just fine. I was also working in lazy for my next project I was about to do. In mach3 the image display was working or everything was working perfect, until my power went out out of nowhere while I was in the middle of scaling the image. Might I add I had already made sure after I posted the gcode that mach3 would show the image on the table display... so after I turned everything back on; hardware and softwares. I tried to repost my gcode image into mach3 again when I noticed that in the image display or table display nothing would show. No image no nothing. I'm pret sure i have all my settings correct... but im not so sure either. Plesde help.ty

5

General Mach Discussion / Yesterday no gcode limit, today 50 line gcode limit

« on: April 29, 2017, 01:11:41 PM »

Hi, I'm having an issue where mach3 only posts a limit of 50 lines of coordinates after I transfer the file from LazyCam. The day before yesterday it worked fine with no gcode limit no matter how big the file was. Now today after I set my depth, scaling, etc in LazyCam I "post code" into Mach3 I only get 50 lines of code. I've tried this already with a small image (under 500lines of code) and a larger image (500+ lines). Please help anyone. Thanks in advance!!

6

General Mach Discussion / Re: Mach3 500 gcode limit

« on: April 28, 2017, 01:36:41 AM »

Thank you. I sent them a message.

7

General Mach Discussion / Mach3 500 gcode limit

« on: April 27, 2017, 10:55:23 PM »

I have bought the license through ebay... sealed copy and all. So yeah I payed around 175$. Everything is working as the program should but I have a limit of 500 lines that Mach3 only reads the rest gets cut off... I've looked for the License Files and have both in the Mach3 folder aswell. "License", and "Mach1Lic". How can I resolve this problem hopefully without having to purchase another License.. and FYI. I'm using it off a computer with no Internet access.

8

General Mach Discussion / Re: only 2 axis moving when all 3 axis are enable!!! HELP!!

« on: January 25, 2017, 08:43:24 PM »

no i dont have a manual for the  ontrollers or motors.. it is a chinese cnc that i purchased off  ebay.. a 3040

9

General Mach Discussion / Re: only 2 axis moving when all 3 axis are enable!!! HELP!!

« on: January 25, 2017, 11:10:19 AM »

These are the motor inputs I have as of right now.

10

General Mach Discussion / Re: only 2 axis moving when all 3 axis are enable!!! HELP!!

« on: January 24, 2017, 09:08:28 PM »

Thanks craig. i have tried what you have told me to do, and yes all axis move when given the inputs... the only problem now is that when i press the up or down arrow keys for the yaxis, the DRO for the yaxis increases and decreases but phisically it is the Xaxis moving, but when i do the opposite as in pressing the arrow keys for the Xaxis, the DRO counts but the Y axis does not move at all. neither vice versing the problem. the Z axis moves as it should be now, by pressing page up, down the Z axis dro counts aswell.