Hello Guest it is March 28, 2024, 08:26:49 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Jerrypower

Pages: 1 2
1
General Mach Discussion / Re: Low voltage on stepper port issues
« on: March 26, 2018, 09:20:54 AM »
Measuring the ports on the PC gives this result.
This is directly at the PC no cables in between.

pin2  4,79v
pin3  4,79v
pin4  4,79v
pin5  4,79v
pin6  3,1v
pin7 -0,249v

pin 2 is step for X
pin 3 is dir for X
pin 4 is step for Y
pin 5 is dir for Y
pin 6 is step for Z
pin 7 is dir for Z

2
General Mach Discussion / Re: Low voltage on stepper port issues
« on: March 24, 2018, 11:00:05 AM »
I'll keep that in mind and try it as soon as I can.
Thanks.

Though, could it be the parallel port that is doing this? To get lower voltage at the card.

3
General Mach Discussion / Re: Low voltage on stepper port issues
« on: March 24, 2018, 10:51:03 AM »
There are no other ways to do the wires to get it to work that i know of.
But is there any way to control the output from the mach3 program, or something else we could do to troubleshoot it?

4
General Mach Discussion / Re: Low voltage on stepper port issues
« on: March 24, 2018, 10:32:53 AM »
I'm bad with these terms, What doe BoB stand for?

5
General Mach Discussion / Re: Low voltage on stepper port issues
« on: March 24, 2018, 10:24:51 AM »
But it worked about one or two years ago.
Is it common that these things breaks?

6
General Mach Discussion / Re: Low voltage on stepper port issues
« on: March 24, 2018, 09:55:30 AM »
The 5th slot for the B axis is also dead, no response at all in voltage. And din't work when we tried it.

7
General Mach Discussion / Re: Low voltage on stepper port issues
« on: March 24, 2018, 09:41:13 AM »
Seems the pictures was too large so I put them here https://imgur.com/a/ITwEF
If it is Ok to post links to imgur.

8
General Mach Discussion / Re: Low voltage on stepper port issues
« on: March 24, 2018, 09:27:04 AM »
X Y and A is working like a charm.
As I mentioned in the first post I moved the wires from Z to X just to test and see if there was any kind of issue with the motors, but they worked there.
And at the same time I also put the working X motors and wires to the Z slot and nothing happened, except the same low 0.21v.

9
General Mach Discussion / Low voltage on stepper port issues
« on: March 24, 2018, 09:04:12 AM »
Hello,

I have some issues with a CnC machine.

The Z axis doesn't work at all.
When measuring the current going through the pins and comparing it to the other axis then the step pin has a permanent 0.21v and thus doesn't work.
I've swapped the cables from the other axis to this one and vice versa and could conclude that there is no issues with the motors and cables.

Measuring the cable it itself gives of 5v (Which all the other cables also does), but as soon as it is put in the step slot on the card it drops down to 0.21v.
No matter how much I try to move it in the mach3 software it doesn't work. It changes position in the mach3 program but refuses to work.

If I remove the cable from the card and then just touch it to the slot where it is supposed to be it does small jumps at first contact, as if the 5v tries to make it move, but then straight away drops down to 0.21v.

Does anyone have any idea how to further troubleshoot this?
Or is it possible to change the voltage at the step port from mach3 itself?

I've tried to start it from a clean profile, but also using the one provided as the software and machine were purchased.

I'm attaching the image of the card as well as the xml.

If you have any idea on how to fix it, or to further troubleshoot to figure out what it is then please tell me! :D
If you need any additional information, then please tell me asap and I'll provide it as fast as i can!



Regards
/Jerry

EDIT: I might have double posted a bit here as it didn't seem to accept it.

Pages: 1 2