Hello Guest it is July 28, 2021, 07:02:03 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - AGOMA

Pages: 1
1
General Mach Discussion / Re: Change direction of the work area
« on: August 22, 2016, 05:49:58 PM »
Thanx guys.
I've tried a couple of things. I and I did get the swap axis to work. So that's good, and I can see in pins and ports that they have mowed from a to b, I and then back to a after reset swap. But the b won't home during doOEMbutton.. Yhy? The Uc300 shouldn't care about that, only what is locked in pins and ports ? Again, thanx all for your help!  ;D

2
General Mach Discussion / Re: Change direction of the work area
« on: August 21, 2016, 04:44:04 PM »
Hello.
Seems like my UC300 isn't compatible with homing a slave axis separated.

I'm trying to swap axis, but can't get this to work either..
Does anyone have code for this.?
I have found some but they didn't work.

I've started with dooembutton for z then y then x with slave a.
Then swapaxis a with b and dooembutton for home b then reset swap..
..but no success :(

Big thanx..


3
General Mach Discussion / Re: Change direction of the work area
« on: August 17, 2016, 11:04:53 AM »
Thanx.
I will try to set up the B axis instead, just to be sure..

4
General Mach Discussion / Re: Change direction of the work area
« on: August 17, 2016, 10:30:15 AM »
Yes I have and yep they do.  :)
Feels like I have tried everything.. Well I will start over.
From the top  :D

5
General Mach Discussion / Re: Change direction of the work area
« on: August 17, 2016, 09:26:46 AM »
I've googled and YouTubeed but I can't get it to work.
Does anyone have an idea what I'm missing?

6
General Mach Discussion / Re: Change direction of the work area
« on: August 17, 2016, 01:28:55 AM »
Yep. It's unchecked.
.. I tried to check it also..

7
General Mach Discussion / Re: Change direction of the work area
« on: August 16, 2016, 04:57:05 PM »
Yes I have one for a and one for x.
They are tested and dedicated in ports and pins.

8
General Mach Discussion / Re: Change direction of the work area
« on: August 16, 2016, 04:26:57 PM »
Hi. Now I got it to work. I and as you say. I was wrong about the coordinates.
Now I home at the front right corner and x+ takes me to the far right and y+ to the left  8)

But I can't get the homing with my slave axis to work.  ???
My slave A axis stops when the X is home. So if The x i not straight I won't compensate for this..

I tried to change to refcombination(9) but not.
Are they any script the home them separately?
Starts at the same time and stops at the sensor?

Thanx  ::)

9
General Mach Discussion / Re: Change direction of the work area
« on: August 16, 2016, 04:55:26 AM »
Thanx Tweakie for your answer.

humm,  controversial topic?? ???
Is it possible for you to suggest new topic so I can change, it is not meant to offend anyone. this is because my bad English.  :'(

I bought a broken multicam machine that I built for MACH 3.
This has its homing in the lower right corner.
I have been using Sketchup with sketchucam.
When I export gcode after moving the zero point to the other side of the job, it becomes empty in gcode. but I can try to move the home position to the lower left corner, so maybe it will be better.

but if I change the Direction Active Low state in the Config. / Ports & Pins / Motor Outputs. it will be mirrored then?

Many thanks for the reply

10
General Mach Discussion / Change direction of the work area
« on: August 16, 2016, 03:21:33 AM »
Hi. First post so please be gentle.  ;D
..and please excuse my bad english.

I can not find how to change direction of the work area?

When I run the machine to home pos, it goes to the lower right corner, which is correct.
But when I run a job I have to run to the upper left corner and put zero because the job would go toward + and not -.

Anybody know how to change this?
see attached image.

Many thanks

Pages: 1