Hello Guest it is August 08, 2020, 11:14:47 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Green Apple

Pages: 1
1
General Mach Discussion / Re: Altivar 320 VFD + ESS Smoothstepper + Mach4
« on: December 31, 2019, 12:48:21 PM »
How do you set up the ATV320 for auto manual control? https://www.se.com/ww/en/faqs/FA332557/

What is this mysterious auto manual control is yet to be discovered and learned about.

2
General Mach Discussion / Re: Altivar 320 VFD + ESS Smoothstepper + Mach4
« on: December 31, 2019, 10:58:01 AM »
Quick update
I downloaded the SoMove application and ATV320 DTM Library.
First impression is that this VFD is highly programmable/customisable and quite complex ... not something to jump in not knowing what to do.

3
General Mach Discussion / Re: Altivar 320 VFD + ESS Smoothstepper + Mach4
« on: December 27, 2019, 02:19:12 PM »
yes, Altivar has a RJ45 jack and  I ordered a cable for it, should be here next week and I downloaded the SoMachine software.
As I mentioned and as you pointed out it out configuration is different I just need to figure out how to program the ATV320.

Erik

4
General Mach Discussion / Re: Altivar 320 VFD + ESS Smoothstepper + Mach4
« on: December 27, 2019, 01:58:04 PM »
Thank you Craig!
I emailed all the points you talked about to Graybar.

But electrical side is only a part of the problem. Looks like logic wiring is different than HY. For some reason all the pdfs that I have read so far on Schneider's web site are generic.

Terminals on HY and ATV320 are different from one another so it is not apples to apples :(

5
General Mach Discussion / Re: Altivar 320 VFD + ESS Smoothstepper + Mach4
« on: December 27, 2019, 10:01:16 AM »
Short story is that I have a friend working for the Graybar Electrical and he put me in touch with an engineer who recommended this VFD.
You're absolutely right, I don't have 3 phase supply so I asked if this unit will work on my DIY shop and I was assured that it would work just fine.
I also got a line reactor as it was recommended.
I have not connected any of these parts yet because as I explained in my first post - I am a bit intimidated by the nominal power and wanted to make sure that I'm doing a right thing.
I will, however, ask my friend to elaborate on all the points which where raised in this conversation and I thank you for them!

6
General Mach Discussion / Re: Altivar 320 VFD + ESS Smoothstepper + Mach4
« on: December 25, 2019, 01:36:31 PM »
According to a Graybar engineer this VFD can be configured to utilize one phase

7
General Mach Discussion / Altivar 320 VFD + ESS Smoothstepper + Mach4
« on: December 25, 2019, 10:02:29 AM »
Hi
Sadly I have zero experience with this unit/brand. At this point, I really really  really looking for an assistance to set the parameters up properly along with the wiring of an ATV320U75M3C https://tinyurl.com/u6wlkzn

This ATV320 is a replacement for a perished Huanyang VFD (HY).
So the Mach4 and the  ESS is currently configured and wired to run the HY.
Unfortunately the interface of the ATV320 looks nothing like HY

I have a single phase 240V to a three phase 2.2kW spindle.

Thank you, Erik.

Pages: 1