Hello Guest it is March 28, 2024, 01:20:08 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Graeme

Pages: 1 2 »
1
General Mach Discussion / Re: License Problem
« on: February 21, 2016, 01:29:20 PM »
Mach3Mill


2
General Mach Discussion / Re: License Problem
« on: February 21, 2016, 12:35:57 PM »
XB not AB. sorry guys I am disabled so find this pretty difficult

3
General Mach Discussion / Re: License Problem
« on: February 21, 2016, 12:34:30 PM »
sorry should have written I can see AB1 to 14

4
General Mach Discussion / Re: License Problem
« on: February 21, 2016, 12:29:00 PM »
ok... My real license is showing mach 3 is closed and I am in the mach 3 folder. XML folder open but canniot see profile? I can see XML 1 then more of the same up to 14 then read me? sorry I really am a beginner

5
General Mach Discussion / Re: Hall of shame
« on: February 21, 2016, 12:22:42 PM »
I purchased my cnc from ebay and although I had already purchased mach 3 software from a legitimate source, when I put my machine together there was an unmarked disk in the box, I assumed this was an installation disk and put it in and it  turned out to be mach 3 licensed to fabio. Now I am a real beginner with all of this and, with computers so I assumed everything was okay, it was guys on the forum who told me it was fake and, what was happening was that it changed from my licence to the fabio licence and was a real pain I complained to the company (I thought) I had purchased from but they were actually in china so no progress there. I would never buy pirated software intentionally  and if I did, I would`nt install it over the real software, its caused me loads of problems so good luck if you can stop those who sell it.

6
General Mach Discussion / License Problem
« on: February 21, 2016, 12:06:29 PM »
I had some problems getting started because my chinese 3040t came with a software disk (mach 3) that I thought was an installation programme for the machine. I had already purchased a real licence and had the correct mach 3 software installed. After help from you guys on the forum I finally got everything running fine (I thought). Everything was fine today until halfway through my first project the cnc began cutting small circles (gutted) I could`nt figure out what could be causing this until I noticed that at the top of the screen mach 3 said DEMO. I have re installed 3 times today,m making sure thatv I removed all previous versions, then I re installed as per instructions and copied license data etc. Every time I restart my project I get about halfway through and then it goes wrong and mach 3 says I am using the DEMO. My questions are; What can make the license disappear during use? and how can I prevent it from happening? so long as my name appears at the top of the mach 3 screen as licensed to everythings fine. As soon as it changes to Demo the cnc starts cutting circles?
Thanks for reading and any advice you can give.  

7
General Mach Discussion / Re: Can anybody help me with these problems
« on: February 21, 2016, 06:04:08 AM »
I would like to thank all who have replied to my post. I`m now up and running, everything working as it should. I would never have got started on my own and I really do appreciate your help. Now all I have to do is create... OMG! :=0

8
General Mach Discussion / Re: Can anybody help me with these problems
« on: February 19, 2016, 02:59:41 PM »
that worked! many thanks to you. I still have no movement from keyboard but at least my original version of mach 3 is back

9
General Mach Discussion / Re: Can anybody help me with these problems
« on: February 19, 2016, 02:26:32 PM »
Thankyou very much, I`ll tery that

10
General Mach Discussion / Re: Can anybody help me with these problems
« on: February 19, 2016, 01:52:24 PM »
Thankyou, I have watched all video`s many times and pause video`s at each step/setting. I have also tried uninstalling mach 3 many times and downloading software from artsoft but license still states licensed to pablo/fabio. I will try again and I will search computer to see if the chinese license is stored anywhere else on my comp because it seems to be automatically installing itselff in the artsoft download. Thankyou for your help very much appreciated.

Pages: 1 2 »