Messages

1

German / Re: Laser M10P1

« on: August 07, 2016, 01:44:55 PM »

Hey Tweakie,

i tried today the laser as we discussed with the paper... unfortunetaly there was no shot from the laser, even though the circuit works with the battery. With the button at the power adapter, a laser-shot is possible, so it should be a problem with the circuit. I took 2 pics of the wiring, may i ask you if you recognise any mistake?






Green = GND
Black = m10p1

Greetz Bernd

2

German / Re: Laser M10P1

« on: June 18, 2016, 11:30:28 AM »

Hey

Thanks for your help, now really the very last question, is it mandatory that the potentiometer has 10k? cause i don't have a 10k one

Bernd

3

German / Re: Laser M10P1

« on: June 16, 2016, 06:02:26 AM »

Hey Tweakie

I have set up the curcuit layout without the power adapter and 4,5V battery and it works. But it shows me at  OV at S100, 2,25V at S50 and 4,5V at SO, shouldn't it be the other way?

Bernd

4

German / Re: Laser M10P1

« on: June 15, 2016, 02:06:19 PM »

Hey Tweakie

Last time to be totally sure...is it at the 1st picture a 10k resistance and at the 2nd one a 10k potentiometer?

1.)




2.)

5

German / Re: Laser M10P1

« on: June 15, 2016, 08:45:09 AM »

Hey Tweakie


I assembled everthing like you told me. I have version R3.043.066 and adjusted all the things as you texted me.
To get everthing right, should i connect a 5 volt source (4,5 also possible?) as +pole with the 10k , the -pole with Gnd and place the gauge in between?

Bernd

6

German / Re: Laser M10P1

« on: June 14, 2016, 08:49:59 AM »

hey thanks you very much . I have the circuit built up and the Gauge shows 0 Volts on the display.... Is this okay??

I have uploaded a Video of the problem.



https://youtu.be/5tLrgn2SL8k

Bernd

7

German / Re: Laser M10P1

« on: June 13, 2016, 06:43:31 AM »

Hey sorry for bothering you again, but may i ask you the last time for help...

Can you pls just connect the pins of the SubD25 with the pins of your control system and further on the pins of the control system with the laser control terminal? pls just mark the connections with lines in the attachted picture

thx in advance i would be really glad for your final assistance...

8

German / Re: Laser M10P1

« on: June 13, 2016, 03:22:24 AM »

Hello Tweakie

sorry i am confused i not understand

Pin17=Dp25(lpt)
Pin16 (output1)= laser pin3
Gnd=Gnd
Pin16 (laser drigger)= pin16 (lpt)
 

Bernd

9

German / Re: Laser M10P1

« on: June 12, 2016, 06:50:04 AM »

Hello Tweakie

I have no designation ( TTL TTH ) in the description of the laser power supply.
I think the TTL TTH with my power supply " WP " is right?
What is "pull-up to +5Volts" ?

Bernd

10

German / Re: Laser M10P1

« on: June 10, 2016, 04:40:49 PM »

Hallo

Probiers mal in English 

I need help tweakie....

i use yours circuit but the gauge show me 0 volts     



Connections wrong?

Bernd