Hello Guest it is March 28, 2024, 10:20:15 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - anchor1

Pages: 1 2 »
1
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 18, 2015, 11:13:22 PM »
pity I cant get a copy of that ,I need xp for work stuff and can't go past win 7 pro  with  xp mode 

2
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 18, 2015, 10:09:08 PM »
not on my pc 12 licenses and counting , also the number for phone activating windows changes too .

3
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 18, 2015, 07:48:40 PM »
Clean install of xp needs a knew pcid . If you image the drive with acronis and do a clean install of windows from that you wont need a knew pcid

Mike

4
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 11, 2015, 07:11:14 AM »
on an xp home I loaded the demo on clean install service pack 2 I had trouble, I then installed service pack 3 and  vc 2013 to get it installed and running

5
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 11, 2015, 06:56:47 AM »
Is it the home version of xp

6
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 11, 2015, 06:22:45 AM »
I have windows xp pro, service pack 3,  32 bit, if thats any help had to install vcredist_x86 2013.
Still waiting for license they deactivated my license page for mach 4 after 10 ,Getting close .
Is yours not installing.

7
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 11, 2015, 05:37:44 AM »
There is a knew version of mach4 out that fixes xp pcid changing now if I could just get a new license...... :)

8
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 09, 2015, 09:18:05 AM »
Thanks blockhead I did some limited testing in demo mode didn't use more than 5% cpu on anything I have done .Not sure what a big file size would be but I made the step over .03mm in vcarve pro and recalculated some raised lettering, that took five min to load into mach4  and was then using 70% cpu while loading ,is that what you mean by slow ,it seemed to cut air alright at maximum speed of the mil ,would break bits if it was cutting steel at that speed.

Mike

9
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 09, 2015, 04:21:04 AM »
So will XP not work as well as 7 ,8  and 10 ,the reason I ask is I have lots of XP boxes in the dead computer cupboard .Will they run slow or what ,they all exceed the minimum requirements plus XP is easy to tame .This is win 7 I am on at the moment just rebooting is a pain with (windows has operations to perform) waiting, waiting ,waiting ,I have never been able to stop it ,8 will never go on one of my computers for more than 5 min its just plain horrible , I don't know about 10 I don't see it as being supported.

10
Mach4 General Discussion / Re: Mach 4 licence not instaling
« on: September 08, 2015, 06:04:26 PM »
I got this back from support:

Hello Mike, the latest version of Mach4 has issues with Xp. The developers and programmers are working on it and when it is addressed i will let you know. Best regards Jim.

Pages: 1 2 »