Hello Guest it is March 29, 2024, 12:58:13 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Tiieto

Pages: 1
1
Modbus / Modbus Problem...
« on: October 14, 2016, 05:14:08 AM »
double post... Sorry...

2
Modbus / Modbus Problem...
« on: October 14, 2016, 05:11:46 AM »
Problem solved!!!

See pictures for the correct configuration:

But this time i had named the Inputs... (that was not the error!)



3
Modbus / Modbus Problem...
« on: October 13, 2016, 03:26:03 PM »
Hello Guys...

I have a Problem By configure my Modbus Input device...

My Hardware:
Modbus TCP Converter (USR-TCP232-410s)
Modbus 16 Digital Input Module (WP8026ADAM)

When i want to configure all 16 Inputs it don't work
When i configure less than 16 Inputs it Works. But the Input #1 is useless...
Mach 4 Diagnostic -> Modbus Shows ne the Second Input as the First...

The Module is in mach 4 configured as:
Function type: Read Input Discreats (0x2)
Function name: Inputs
Slave Adress: 10
Modbus register: 02
Register count: 15 (works without input #1)
Or
Register count: 16 (don't works at all)

I use the Modbus TCP converter because I use the smooth stepper Ethernet..

I want everything via network...

You may have a solution for this problem?


4
Modbus / Re: Best way to get extra outputs
« on: August 02, 2016, 02:06:36 PM »
Hey there...

Sorry for the late reply...
Do you still need more output hardware for your Project?
Maybe i have a good solution...

Kind Regards...

5
General Mach Discussion / Mach3 or Mach4 whitch one should i use?
« on: August 29, 2015, 06:35:40 PM »
Yes i did...
There Is a PlugIn for mach4 available...
Ist a Little different then the PlugIn for mach3, i tryed it in a Virtual machine - Software chrashes - i Need to try again on a native machine...
Or does someone else tryed it on a native machine?

6
General Mach Discussion / Mach3 or Mach4 whitch one should i use?
« on: August 29, 2015, 06:54:30 AM »
Hey guys...

I currently Build up my Self-Development cnc Mill / 3D Printer (all in one)

I choose Mach dir the Software i want to use but im Not sure whitch one i should use finaly...

For Mach 3 there Is an add on for use the CNC Mill as an 3D Printer.

Does an 3D Printer add on exists for Mach 4, too?

By the Way: i use the Smooth Stepper Ethernet for connect the machine to the Computer & a RS485 to Ethernet Converter to Control the VFD rpm & running Direction.

With Mach 3 i can Control 6Axis - this will be enough for my "Dream machine" if i Trick a Little...

My Dream machine (the final Status for my Self-Development) has the Standard 3 Axis (XYZ) and 2 circular Axis (AB). The C Axis i want to use for Control the automatic Tool Magazine (chain) to move the Tool i Need into the machine-work-room...
But 1 Axis will be need for Using the CNC as an 3D Printer... Maybe Switching the Tool-Magazine Stepper Motor to the 3D Printer Stepper Motor in 3D Printer Mode and Switch back to the Tool-Stepper-Motor in CNC Mill mode...

But maybe Mach4 can Do this more elegant?

What Is your recommendation?

Kind Regards...

7
Sure, i will..

But the machine isn't Complete yet... Still "here a Part and there a part..."
I will Post some Pics (& maybe Video) after machine Is Complete Build up...
I just Register in this Forum because i choose Mach (Not sure mach 3 or mach 4) for the Software i want to work with...

Kind regards...

8
Hi there...

I am the new one and come now more often...  :D

I´m from Germany and i currently build up my own CNC Mill / 3D Printer (all in one)...
Currently the machine has 3 axis and will get 2 more axis in the near future and a fully automated Tool magazine (Chain)..

This machine is a self-development by myself...

Kind Regards...
Tiieto

Pages: 1