Messages

1

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 03:49:38 PM »

turning off axis don't track it down... only one active and still the problem.

2

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 03:47:58 PM »

Tested also.
Took the new Mach4.2.0.2673 and the old Darwin 1.2178 and it worked not.
The old Mach4.0.1.2461 and the new Darwin 1.2646 and it works!!!

All running under Win 7 32 bit enterprise.
What make i wrong?

3

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 10:19:14 AM »

Yes so it is. 2178 working 2472 not
No difference. Can see the version 2646 in the plugin overview but same issue..

4

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 10:00:57 AM »

The funny thing is, i started a backup mach4 version.
Mach4.0.1.2461
Darwin 1.2178
25 khz
Motor 0 > 800Steps/Unit >Velocity 1800 ->acceleration 250
Motor 1 > 800Steps/Unit >Velocity 1400 ->acceleration 100
Motor 2 > 133.33Steps/Unit >Velocity 400 ->acceleration 20

And there is no problem with the darwin??

5

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 09:17:42 AM »

Art:
I have a motor with 800 steps per mm
a Velocitiy of 1000 units/min
so it is about 13khz
i've set my pulse setting to 24khz

That should be ok?

6

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 08:20:35 AM »

Dear Art, sascha once again.

I'm getting the "Darwin Buffer Error - Motions  out of Bounds" error, when i click enable.
What i did:
Removed the old Mach4 installation
Installed the version 4.2.0.2673 Mach 4 Version, and it's licensed with a new ID
Installed the version Darwin Setup V2 2611, and under System Information i can see it's licensed
Installed the VCRedistX86  for vs2013.
But under System Information i can see only a Version of "1.2472" of the Darwin Plugin.

Can you help me with my error?
When i switch off my controller card and click then "Enable" the error is gone? WTF?
Thank you
Sascha

7

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: May 20, 2015, 12:45:23 PM »

Art,
its running, the fix make it.
After all setting ( that where gone ) the machine is now running thru the complete programms.

But one more questions, when i mill ssome circle's, the circle's get not round, they are more elipse.
The machine stumbles when milling the circles.

Do you have any hints?
Sascha

8

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: May 19, 2015, 09:58:11 AM »

Hey Art..
ok, then i have to wait, hopefully they fix it very soon.
Sascha

9

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: May 19, 2015, 07:47:04 AM »

Yes i get it.
Thats very sad because my machine has to run. I can't produce at the moment.

10

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: May 19, 2015, 04:09:41 AM »

Hey Art,
yes i loaded the file via help--> About--> Load license file.
My file in the folder mach4hobby/licenses looks like this:
# License created: 17-05-2015
# MAC: 080B-0019996A7E89
# Expires on DD-MM-YYYY: 10-12-2044
# Licensed application:
#    Name: "NF_DARWIN"
#    Description: "Darwin Plugin License"
# Features included:
#         M4_DARWIN
# Custom data:
#         url=http://www.machsupport.com
#         support=support@machsupport.com
# === Start copy after the BEGIN LICENSE line and ===
# ===      finish before END LICENSE line         ===
----- BEGIN LICENSE -----  
......

I downloaded the file again from my account. with the same problem.

Sascha