Hello Guest it is March 29, 2024, 08:30:22 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - efrem

Pages: 1 2 »
1
Galil / Re: Mach3 + Galil
« on: April 29, 2007, 07:53:04 PM »
I try to retrofit a Jafo milling.

I got a program called DMC Setup and it seems to be like your wdsk , it's visual and you can change all the variable al the screen without typing them.

Do you know if I can get motion from the serial cable ? , if yes, I wont waste my time over the ethernet. Serial communication seems to be very fast !


2
Galil / Re: Mach3 + Galil
« on: April 29, 2007, 07:29:52 PM »
I forgot, it's possible to get motion by the serial connection and does mach3 works with this connection ?

3
Galil / Re: Mach3 + Galil
« on: April 29, 2007, 06:48:32 PM »
Thanks roodesign,
 
I upgraded the fimware with the serial cable and now it works. My problem now is that I can connect ( I have done all the steps in the help file ) by ethernet but the connection is very very slow, ureliable and I lost 50 to 75% of the ping that I send to the controller. I can connect 1 time out of 10 and I got a lot of timeout errors.  I have set the ip by the serial cable and the connection by ethernet still unusable. How can I solve that ?

My other question is; do I need to set my servo drives in velocity or torque mode ?

Also, when I try to move the motor in the terminal, it say that my motors are disable. How can I enable them ?

4
Galil / Re: Mach3 + Galil
« on: April 23, 2007, 06:09:33 PM »
I have a rooter only for my pc and the galil. My ip is 192.168.1.100 and the galil 192.168.1.150. The router is not on the dhcp mode.

5
Galil / Re: Mach3 + Galil
« on: April 22, 2007, 10:54:17 PM »
I'm trying to make work my galil 2140 and it's a real pain. The controller disconnect every time, forget it's ip and I got the error 15 when I try to update the firmware by ethernet ... When mach3 start with the plugin, it write that the answer is too long ... Am I the only one that got thoses troubles or it's normal ?

6
Galil / Re: Galil Status
« on: February 15, 2007, 09:28:44 PM »
The galil products seems to be more professinal than Grex. Grex seems to be a hobby project ... I don't have money to waste in this. A galil card keep a good value but I don't think so about the Grex ...

7
Does mach3 support thoses industrials networks with a plugin ?

8
Galil / Re: Galil Status
« on: January 28, 2007, 01:44:34 AM »
Brian, can you tell me witch version of galil will works with mach3. I have a DMC-2140, will it works ?

9
General Mach Discussion / Grex and mach4 ( 3 )
« on: October 18, 2006, 09:01:37 PM »
Does anyone knows the progress of the new firmware of the Grex that will be used with the Grex plugin of mach3 ? And do you also know the progress of the plugin for mach3 ?

Thanks

10
General Mach Discussion / Grex and his Mach3 addon
« on: September 09, 2006, 07:50:19 PM »
Does anyone know any news about this. It still in beta phase or it's working ? When the first release will be online ? etc ...

Thanks

Pages: 1 2 »