Hello Guest it is March 25, 2023, 01:30:23 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - JTW

Pages: 1 2 »
Still need help. We were going to take it apart to reverse engineer it but time constraints from other work keep getting in the way. Also seems a waste of time if someone can just give us a wiring diagram. So nothing to report for now :)

We will not give up though!

General Mach Discussion / Re: bolt circle pattern problem
« on: April 04, 2015, 09:11:49 PM »
I would make a test piece with co-ordinates that I calculated myself and see if the problem persists just to eliminate that possibility. Is the machine based on servos or steppers?

Show"N"Tell ( Your Machines) / Re: The Laser Project.
« on: April 04, 2015, 08:36:09 PM »
Just to confirm, drilling the peltier is not going to work. Major risk to break the series connections inside but the plates on each end are usually ceramic and the pressure from the drill will just shatter it. You can get circular peltiers with holes already in them though.

General Mach Discussion / Re: bolt circle pattern problem
« on: April 04, 2015, 08:24:45 PM »
Are the co-ordinates ok or is this a hard problem? Like backlash?

VB and the development of wizards / Lathe turret ID and installation
« on: April 04, 2015, 08:23:13 PM »
I scored a nice turret on ebay but have no documentation or even a clue to the manufacturer. I think maybe Duplomatic or Pragati... Can someone with previous experience please provide a little guidance on how this needs to be set up and how the control of it should be performed? Thanks in advance!

Show"N"Tell ( Your Machines) / Re: VDF/Padovani Rescue
« on: April 04, 2015, 08:05:15 PM »
Getting closer to that manly swarf, Dickeybird! Thanks for the compliments! Today we did a bit more on the control panel. Then we must figure out the tool turret and finalise everything.

A few minutes with angle aluminium and TIG welder

Windows 7 Install

Much nicer to look at than Sinumerik 805!

MachIII installed

Only major problem now is connectivity issues. The USB Smoothstepper goes to live on a laser cutter and we replace it with Ethernet Smoothstepper as per advice on this forum. USB Smoothstepper is just not reliable for an industrial machine.

General Mach Discussion / Re: Weird backlash issue
« on: March 26, 2015, 03:56:23 PM »
Confirmed. Balasz from CNCdrive was very helpful and we solved the problem by tuning the PID settings. :)

SmoothStepper USB / Re: Cable length issues
« on: March 26, 2015, 03:53:02 PM »
Hi Jeff, agreed. Should have gone with the ethernet version. Tried the external power like you said, some improvement but still unusable. I guess time to get an ethernet smoother stepper!

Show"N"Tell ( Your Machines) / VDF/Padovani Rescue
« on: March 18, 2015, 07:35:05 PM »
Still a work in progress but it starts to look like we can finally settle on Mach3 and start putting things back together without worrying about taking them off again 5 minutes later! We were looking for a large lathe and came across a suspiciously cheap big old lathe. VDF is a German brand so I was willing to take a look. The machine was in pieces, could not be seen running but I was assured she was ok. Yea, sure... Mechanically she looked ok and the price was barely above the scrap metal rates. Little to lose, much to gain. Sold! 800mm max. diameter and 2000mm bed, quite a large lathe and just what we need to complement our other machines.

We got the machine back to our shop and surprise surprise she wouldn't start. The backup battery had failed. But here is the weird part. The machine was actually a home-brew retrofit of a Padovani system with a Sinumerik 805. But to reset the parameters you needed either an original Sinumerik keypad or this special software. The keypad was 500eur at best on ebay, and the software was impossible to find. We called a service center who immediately tried to screw us over and wanted 2000eur to reset the machine. Enter MachIII. We spent a few days reverse engineering the machine as we had absolutely no documentation. We opted for a smooth stepper, PMDX126 and PMDX107. The control panel has a PC built in instead of the PLC but this is not operational yet due to cable length issues. The machine is running from laptop but not yet really finished or reliable as we would like. There is also a strange backlash issue, which appears to be electronic in origin as the mechanical system is backlash free. Still we are cutting metal with it.

All in all, it is great to now have a control with new parts and an active support system. Our other machines are still running on older controls and we constantly have troubles with support, which is actually not a bad thing as we are now quite adept at diagnosing and repairing our equipment! Even though the machine is not ready yet we are already planning to fit MachIII to our oldest CNC lathe as it is built amazingly well, also German but the machine is far more complex so we leave that until Christmas shutdown!

Machine arriving on back of truck.

Red screen of death!

Original Sinumerik 805 installation

PMDX, Smooth stepper and CNCdrive parts after installation

In service!   ;D

This is the next step. We found an 8 tool turret on eBay for 200 American dollars. A CNC lathe that cannot change it's own tools is not much of a CNC when in a production environment. We have no idea if this thing works, how it works or even who made it. We have to reverse engineer it just like we did with the machine. For the price, like the machine, we are willing to give it a go. When the wins are much bigger than the potential losses you are crazy not to attempt it, even if we fail we will have learned something.

General Mach Discussion / Re: Ballnose Bits
« on: March 18, 2015, 07:00:29 PM »
I used to work for a company that made cutters for wood working machines. You need sharper cutters than for metal, although some hardwoods need metal cutting tools! Ball noses are great for 3D profiling, and MachIII is perfect for the job too, our older machines have to be drip fed for the much longer programs that don't fit in memory, Ger21 is right, use 2 flutes and as small a stepover as possible. We rough with a straight ripper, semi finish with a 12mm ball nose and then use a 4mm or even 2mm for fine details. If you want precision then sanding should be minimised. Let your machine do the work. If your camware has a remachining option to save time with smaller tools, use it!

Pages: 1 2 »