Hello Guest it is November 24, 2020, 01:25:49 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - johndolecki

Pages: 1 2 3 4 5 6 7 8 »
1
I see that fusion 360 has several post processors listed what is the difference between them and which on should I use.

1: Artsoft
or
2: tormach. ( mach3 not pathpilot)

If i want to add a 4th (A axis)  axis to my mach 3 which one should i use.

thanks but im trying to understand while learning the cam in fusion 360

thanks John


2
Modbus / Re: Who can I call to help me setup this automation direct vfd
« on: December 19, 2018, 07:39:13 PM »
aggggggggggggggggg

i changed computers now my modbus dont work again!

3
Show"N"Tell ( Your Machines) / Boxford Duet desktop CNC
« on: July 02, 2018, 08:07:13 AM »
Acquired two Boxford Duet desktop cnc machines in an auction.
The software that came with them is DOS based and i would like to update them. Luckily the manuals i got have the schematics.
I also would like to use the existing electronics if possible.
The DB25 pin-out shows the pin numbers and functions but there are a few I'm unsure about.

Has Anyone convertered one of thes yet to Mach 3/4? There are some old post but the are incomplete.

thanks, John

4
Finished Screens / Re: Portrait Touchscreen - New
« on: June 05, 2018, 02:54:25 PM »
Can we download that screen set somewhere?

thanks

5
Screen designer tips and tutorials / Changing PNG color
« on: April 02, 2018, 09:03:10 PM »
I would like to change the greendro button image to a different color but when I do and save the image. I can't seer the numbers anymore?

What did I do wrong?

Thanks john

6
Thanks the license transferred
Now to figure out why the machine won’t move

7
General Mach Discussion / Changing computers and moving the license
« on: March 30, 2018, 06:06:27 PM »
I'm changing computers my old computer has the license on it

How do I get it to my new computer.

Also I running unlicensed on my new computer to set up the I/O I have a Ethernet smooth stepper.

Will the demo still generate motion signals cause I can't se m to get any movement when I try to jog the machine.

I know I read about moving the license but I can't seem to find that post anywere.

8
Show"N"Tell ( Your Machines) / Re: new control panel
« on: March 21, 2018, 07:19:17 AM »
It's a Bridgeport Series 1 R2E3

When i got it the DC power supply was shorted. So i replaced everything with new controls but keep the Factory DC servos.

Ethernet Smooth stepper, CNCDrives servo drivers, 80 volt DC power supply. AMT-102 encoders. Used the factory enclosure and servo cables.
Automation direct VFD single phase to 3 phase so I'm using the original motor.



9
Show"N"Tell ( Your Machines) / Re: new control panel
« on: March 20, 2018, 07:55:34 AM »
Started moving the buttons around in Mach 3. i started with the factory  1024 screen set.

My workstaton is a board on to of a garbage can.

Do know why the pictures dont post in proper position??

10
Show"N"Tell ( Your Machines) / Re: new control panel
« on: March 12, 2018, 03:15:29 PM »
Mach3 seems to conform to the vertical screen. but the boxes need some resizing.

I don't thing the touch screen likes windows xp as its acting goofy

probably gonna switch computer to something more sutable to mach 4

first picture is suppose to be vertical??

Pages: 1 2 3 4 5 6 7 8 »