Hello Guest it is March 29, 2024, 06:35:48 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bbcnc

Pages: 1 2 »
1
LazyTurn / Re: Cant seem to cut all material
« on: August 18, 2016, 09:24:13 PM »
here is the g-code

I also do not need the cut at z0...that would hit my live center..whats up with removing that, dfx wise?

2
LazyTurn / Re: Cant seem to cut all material
« on: August 18, 2016, 08:03:42 AM »
also not too worried that the part in the front never came into lazycam, will just program with mach

3
LazyTurn / Re: Cant seem to cut all material
« on: August 18, 2016, 08:03:00 AM »
you will notice all the leftover material, it does not leave a clean looking final product

4
LazyTurn / Cant seem to cut all material
« on: August 18, 2016, 08:02:21 AM »
I have come back to an old project but can't seem to remember how I fixed this issue in the past...I can't seem to get a clean final cut.  Really appreciate the help

The part in the front was supposed to be for a cut to be even with the part its attached to, this was for a final cut off to come in after (which I can program separately without lazycam)


Let me know if you need any other information

5
LazyTurn / Mach not liking all this code
« on: March 04, 2015, 11:03:18 AM »
thanks rich let me know if i can post anything else

6
LazyTurn / Re: Need help with finish cut after rough..Thank you all!
« on: February 27, 2015, 09:36:29 AM »
thanks rich for the dfx as I now know what plane to draw in but here is what I am struggling with

This is my rough cut, there looks like there is material left to be cut but when I try to run ANY kind of finish pass, the program says there is no material to be cut..or is this as close as i am going to get

7
LazyTurn / Re: Need help with finish cut after rough..Thank you all!
« on: February 27, 2015, 01:34:27 AM »
i just feel like I am missing something...even with this I am having the same issue

8
LazyTurn / Re: Need help with finish cut after rough..Thank you all!
« on: February 27, 2015, 12:53:39 AM »
dfx posted

If I can post anything else at all please let me know..thanks again to anyone who can take the time to check it out

Also, my tool looks huge compared to everyone's....

9
LazyTurn / Need help with finish cut after rough..Thank you all!
« on: February 27, 2015, 12:48:39 AM »
I have read and read but think I am missing a huge element to this.  This is as close as i can get.  I am trying to get a clean finish cut but am just running into trouble no matter what I do.  Ill include as much info as I can in pics

I cannot do any kind of finish cut after the first rough cut.  Next pic is just rough/finish together.  Added roughing tool and finish tool setup

rough
http://www.mscdirect.com/product/details/78233756?rItem=78233756
blade
http://www.mscdirect.com/product/details/78639176?rItem=78639176


Finish tool
http://www.mscdirect.com/product/details/09829151?rItem=09829151
blade
http://www.mscdirect.com/product/details/78233756?rItem=78233756


I scincerely thank anyone who can give me a little help

10
General Mach Discussion / Re: Threading Wizard help
« on: June 11, 2014, 12:44:59 AM »
That did'nt help although I feel I am getting closer to the source of the issue.  When using simple thread wizard and going to run in, I tell the wizard I am using tool 4.  Once I start the program my dRO changes from the offset for tool 4, to something else.  I am not sure what offset it resorts to but it isnt the one I set up for my threading tool

Pages: 1 2 »