Hello Guest it is October 03, 2023, 05:54:23 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Bear

Pages: 1 2 »
General Mach Discussion / Re: setting kernal speeds on Mach 3
« on: December 15, 2007, 06:34:12 AM »
Merry Christmas,
Could help me with kernal speed as Im not much up with computers.

General Mach Discussion / Re: Unspecified failure message
« on: July 14, 2007, 06:35:09 PM »
Hi all,
Brian ,no joke,I think the world of this software!
 I had never seen this  error report before.
Mach was going thru "it's process " and I was
unaware .
 I think this system is "Great" !
 My only wish!!! I could figure how to conect to
this hatefull Fadal !
 Thanks ,

General Mach Discussion / Re: Cutter comp
« on: July 07, 2007, 09:19:52 AM »
 Maybe youre holding an offset ,not calling cancel before ,or after using an offset ?

General Mach Discussion / Re: Unspecified failure message
« on: July 06, 2007, 06:31:31 PM »
 Seems there is a lot of interesting "Flags in Mach###, however ,as in my cases, MY Fault,,,.
Had an interesting one .Tool # tool large ?
Well , I had wanted the machine to "start from here".As it was ,I got impatient and restarted,
well, Mach### was correct ,was doing what I wanted and would not accept another tool
# or offset ! WOW,  what a great system !!


General Mach Discussion / Re: Cutter comp
« on: July 06, 2007, 06:17:33 PM »
Doesnt the tool # call up the offset page,where the offsets are entered ?
(Mac-2 user)

General Mach Discussion / Re: Need a motor recommendation
« on: July 06, 2007, 06:07:46 PM »
Hi All,
How do you run these R.P.M.s and those feed rates ?
10/15 thous. deep,less?
I cannot get anywere near that,end burns up,vib,noise,etc.
1/4 or less maybe for O.D. depth, feed rt.
Machine is B.P. retro/2 hp.apx,52 IPM.feed.

Newfangled Solutions Mach3 Wizards / Unsure relays/mach2/3
« on: January 19, 2007, 05:26:08 PM »
Hi all,
am wondering why my machine blows "main" fuses if main power is turned "on" before computer is "on" or for that matter "off".
if i start computer (XP) and then energize Power&BOB things are fine . If I turn computer off first (shutdown Mach ) then
I loose 2 of 3 fuses. ? is I think I have the motor (3ph440) hooked to the relay outputs (M3 to one relay & M4 to another
and works fine ) and maybe I should change the "Hi" to" Low" ?   

Hi  Poppabear,
 Bear here ,some of "us" thankyou!


G-Code, CAD, and CAM discussions / Re: tapping head cycle?
« on: October 22, 2006, 04:52:20 PM »
I  apologise,
unreservedly ,  with great regret, with much sugaring and sorrow.
as I read as the second post today.
 this insubordination ,   Will Not Happen Again   !

G-Code, CAD, and CAM discussions / Re: G71, G70 roughing, finishing lathe
« on: October 22, 2006, 04:38:50 PM »
G70 is usuall ya used for finish profile
G71 "                      " rough "Z" axis  profile(lathe)
G72 "                      " rough "X" axis profile(lathe)

Pages: 1 2 »