Hello Guest it is April 17, 2021, 02:58:03 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Roy Smart

Pages: 1 2 »
1
General Mach Discussion / Error Messages
« on: March 26, 2021, 01:01:04 PM »
Hi,
    I have just installed a UC100 USB Motion Controller on my Windows 10
computer but when I run MACH 3 I am getting an error message "Printer
Port monitor only" Can anyone help with a solution to stop this?
Regards
Roy

2
General Mach Discussion / Re: Mach 3 no communication with CNC machine
« on: March 22, 2021, 02:31:38 PM »
 Many Thanks for your reply.
I will go for the UC100 as it has also been recomended by others.
Again many thanks your help is much appreciated.
Best Regards
Roy

3
General Mach Discussion / Re: Mach 3 no communication with CNC machine
« on: March 20, 2021, 01:15:38 PM »
Hi thanks for the answer. Can you advise what Model Motion Controller I should fit?
My current computer is a Windows 10 Home M/c  Version 20 M2. Can I use other
software on this machine or does Mach 3 need to be run on a dedicated computer?
Regards
Roy

4
General Mach Discussion / Mach 3 no communication with CNC machine
« on: March 19, 2021, 01:23:32 PM »
Hi All
     I have the following problem can anyone Help?
 My old computer was working ok with Windows XP but after a crash it is now U.S.
My new computer has Mach 3 installed but it will not drive the cnc controller. I
had an engineer fit a Parrallel card to run the cnc but it will not work. Is it due
to the 64 bit opperating system on the new machine? If that is so will the machine
work if i fit a parralell/usb converter lead?
As you have probably guessed I am a bit confused with this problem. Any help in
pointing me in the right direction would be appreciated?
Best Regards
Roy

5
FAQs / How can i cut 2mm Styrene sheet correctly and at what speed?
« on: May 15, 2020, 12:27:50 PM »
Hi
   I have a 2030 machine ( A cheap one from China) and I am having difficulty with the speeds and feeds for cutting 0.5mm to 2mm Styrene Sheet. Whatever speed and feed rate I use the styrene is melting and clogging the cutter.  Is there a list somewhere to give me speeds and feeds for various materials.
The only other material I use at the moment is thin plywood 0.5mm to 3mm and there I have no problems at all.
Many thanks for any advice
Regards
Roy

6
General Mach Discussion / Re: Parallel Port Problem
« on: December 02, 2013, 12:05:06 PM »
Many thanks for your help Jeff.

Best Regards
Roy

7
General Mach Discussion / Re: Parallel Port Problem
« on: December 02, 2013, 10:35:12 AM »
Hi Kolias,
             I purchased my new computer and had Windows 7 put on it as I anticipated a problem,
what I did not expect was that the parallel port would not work on a 64 bit OS.
I can not see a way out of this as all new computers are 64 bit as I understand it.

Regards
Roy

8
Hi,
    I had the very same problem when my 3040 was new. After weeks of trying to sort it out we found
a damaged wire to the motor making the noise which made it loose signals. The wire had a small cut in
the insulation which opened and closed as the machine moved and the wire rolled up  therefore
interupting the signal. 
I advise check and replace (if required) any suspect wiring.

Regards
Roy

9
General Mach Discussion / Re: Parallel Port Problem
« on: December 02, 2013, 09:18:08 AM »
Hi Hood,
           You have identified the problem for me. I purchased a new computer system which is a
64 bit machine, this is therefore a big problem which i was unaware of.  Is there any way i can
use the parallel port on this machine? Or is there any work around to solve this?

Regards
Roy

10
General Mach Discussion / Re: Parallel Port Problem
« on: December 02, 2013, 08:01:49 AM »
Hi Hood,
            Many thanks for your reply and help. I have changed the config setting to
E010 as in my Resourse Settings but it has no effect. In the Diagnostics page I am
getting Simulate in the Pulse Frequency Box, I am thinking that signals are not getting
through. Any other ideas?
Regards
Roy

Pages: 1 2 »