Hello Guest it is March 29, 2024, 05:25:55 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Ghantos

Pages: 1 2 3 4 5 6 »
1
Dear Friends,
i ask if any body have an idea how to make a "Counting" of inputs trigs.

what i need is thay every time input #1 is active to increase the DRO by 1

please Note that the input trig  maybe longs 2-3 seconds but i want to count only when its change the Status( it means i cant use a loop and to check the signal "IsActive").

please its very important
thanks


2
Modbus / Mach3 ModBus Digital Inputs/ Outputs Controlling.
« on: September 03, 2017, 03:46:28 AM »
Hello Friends

i just want to know, what is the maximum Digital  I/O's i can configure By ModBus??
is it only 64 in and 64Out??

in my machine i have about 18 Slaves  mouduls that each one has 8In an 8 Out  and each one has an adress by the DIP switch working With RS-485.

For sure, i dont have 104 Inputs and 104 Output but the configration of the machine is like this.

also let me know how to access these I/O by VBA Macros, i Mean how to read input and how to activate an Output By VBA Macros!!

please send me some examples or the function Syntax in VBA for this.

i will be happy if any body can help me and i will really appriciate this.
regards
Ghantos

3
Modbus / ModBus speed and Homing Switch/ limitswitch inputs
« on: August 30, 2017, 03:14:54 AM »
Dear All,

i want to use to modBus for Mappping Home/ limitswitch  inputs.

is the the response speed of the all system is recommended for this function??

somebudy told methat  its not recommended to do homing/ limitswitch because of the little Delay !

please ley me know your idea!
regards'
Ghantos

4
Modbus / Re: Modbus and Timing
« on: August 30, 2017, 03:11:13 AM »
Dear mr. Peter
i want to use to modBus for Mappping Home/ limitswitch  inputs.

is the the response speed of the all system is eunght for this function??

somebudy told me its not recomended to do homing/ limitswitch because of the little Delay !

please ley me know your idea!
regards'
Ghantos

5
Modbus / Re: Homann designs modbus modio mc-01
« on: August 24, 2017, 01:18:05 PM »
Dear Sirs,
I want to retrofit my machine Biesse Rover 346 RT 480 of CNI.
I need to use mach3 for this.

I want to use the all the I/O modules intact!!
The I/O digital modules are ENET SIR88 of CNI.

Does any body know which SW and HW I need to go that!!
Again, I don't like to replace the original modules and drives.

Is the standard TCP/IP modbus of mach3 can make the job??
Please reply
Regards
Ghantos

6
CS-Lab / Re: CSMIO-IP/S or CSMIO-IP/A for a servo controlled router
« on: August 23, 2017, 03:31:52 AM »
dear Sirs,
i have a Biesse Rover 346 to retrofite and to replce the Old controller of RT480.

i dont want to replace the I/O moudle of the system and i want to try to control it by ModBus connection.
for the axes and spindles motions i want to use only CSMIO-IP/A without using any Digital OUTPUT/INPUT!!!

it means, i want to CSMIO-IP/ A and ModBus at the same time because i dont want to destroy the Original connections of the machine

is it possible??
please only persons with experince need to answer me or any body sure about the answer!!
regards
Ghantos

7
CS-Lab / Re: CSMIO/IP-S vs DELTA ASDA-B2
« on: October 05, 2016, 02:40:47 AM »
Dear Sirs,

sometimes and randomaly, i get "Internal Error" WaitForMove error when i run the M6 macro From CS-lab for ATC tool changer??

often, this problem come when the Z axe move down to pick the tool.

an ePID error appere for no need, the z Axes move smoothly no problem.

most times i get the error number in line belongs to the Sleep() function and the WaitForMOve().

anybody face this problem before??

regards
Ghantos


8
General Mach Discussion / Re: Upgrading to latest version of Mach 3
« on: October 05, 2016, 12:38:20 AM »
Dear Hood, and friends

if i already custemized some buttons codes, what happen to the code inside??

what about the genreal Configration, Pots and Pins... ??

where is the XML file located?? and whitch data it has??.

please advice!
best regards
Ghantos

9
General Mach Discussion / Re: tool changing gcode for no toolchanger
« on: August 28, 2016, 06:55:12 AM »
Hello Freinds
 anybody has a Mach3 Macro for ATC (M6) without feeling the sensors for "OpenCollet" CloseCollet, ect....??

really i have no free inputs to connect . and for me i don't care about this!!. i know that this not so efficent but i will try do like this.

maybe in the future i will do this.
regards
Basim

10
General Mach Discussion / Re: Mach3 in relation to alphaCam
« on: March 15, 2016, 03:48:16 PM »
Hello friends,
I use alphacam 2014 to generate Gcode post for mach3.
Normally a make many separate programs with many simple shapes and toolpathes.

I ask if there is a possibilty to send from alphacam the program directly to mach3 without using "load Gcode"   

It means, as soon as the program is been generated i want to press a botton maybe in alphedit to send the program to mach3 and to start the job

Pages: 1 2 3 4 5 6 »