Hello Guest it is December 08, 2019, 01:45:23 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - andysilvester

Pages: 1
1
FAQs / Re: Wiring Limit, Home and E-Stop Switches
« on: May 26, 2016, 04:39:46 PM »
Thanks for the quick reply! My problem with changing the wiring is that I spent more than a day running the wires neatly with sleeving etc. and would prefer not to rip it all out unless I really have to. I guess I was too confident of success having taken advice from sites and forums that my setup would work. Half of it - the home and -- limits does work (!) so I'm hoping to get some guidance on either the inputs screen or maybe from someone who knows the Uniport BoB.

Cheers, Andy

2
FAQs / Re: Wiring Limit, Home and E-Stop Switches
« on: May 26, 2016, 03:18:07 PM »
Spent a good few hours trying to figure my limit switches out on the 'Inputs' page and have ended-up here for help!
I've fitted two switches on each axis (X2 mill) - 'Home' (normally open) are wired individually to my Uniport V2 on inputs 10,11 and 12, and work perfectly for homing and -- limits. The problem's with the ++ limit switches which are all wired in series (normally closed) to input 13. Now, on the Uniport v2 only inputs 10-12 have +5v provided internally, so I've jumpered +5v to the input pin for #13. I reckon I've tried every combination of value on the inputs screen to get the ++ limits to show on the diagnostics screen when operated. I have the E-stop enabled and set to pin 15, but not wired.

I've read the Uniport's documentation, I've tested the wiring and the input by removing a direct short from the input's connectors. I also swapped the wiring to the pin 15 input and changed the values accordingly. Nothing! Any ideas please?

Cheers, Andy

3
Well, to respond my own question (!) which I also posted and had answered at the Warp9 forum....the configurator has done its job matching the IP address to the Ethernet card; no other missing magic involved.
I should have been looking for the smoothstepper ESS config in Mach3's 'plugins' menu item, and yes, there it is!

I'm not really sure the second 'issue' is worth pondering, if indeed it is an issue. There has to be a logical relationship between steps/pulses and calibrated axis movement and my calcs. bear this out, so I'll move-on and try to forget the previous confusion.

Andy

4
1. I added an ESS board to my hobby cnc mill to eradicate some pc/noise issues and I have everything communicating and with stepper control. I made a new Mach3 profile and set about changing some stepper directions and the ESTOP port issue - all done. I'm aware I've unexpectedly missed-out on the process of configuring the ESS for stepper frequency, etc, and despite hours of seemingly going over the same process with the 'configurator', can't get to the page to do this. I've added and removed the jumper for BOOTP many times, powering up and down before/after, but running the configurator doesn't bring up this page (should it??). Ethernet adapter is talking to the ESS, so IP addresses are OK, right?

2. I'm also needing to revise my steps-per (mm) figure in Motor Tuning, and I'm pretty sure I had a figure of 2000 working before the ESS was introduced. HOWEVER, with my setup as follows:

  • Direct stepper connection to leadscrew with 5 TPI, so one rev = 0.2" or 5.08mm
    Standard steppers with 200 steps per rev and x10 microstepping = 2000 pulses per rev
    so dividing 2000 by 5.08 I get a 'steps per mm' of 393.7.
this figure works for axis calibration but how could it have been working with 2000 'steps per' before? (If indeed it was, perhaps I should up-the-medication.......)

Any reassuring words will definitely help!

Cheers, Andy
Oxford, UK

Pages: 1