Hello Guest it is March 28, 2024, 12:46:43 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - alexcfw

Pages: 1
1
General Mach Discussion / Re: Jog not working?
« on: June 23, 2013, 08:23:07 PM »
Hi, Hood. Thanks for your support. I used MPG then motor can turn continuously but unconditional movement.
 I Changed the JNC-40M USB card to new USB to Parallel breakout board, then Jog key can work well and motor also turn with good sound. When i used JNC-40M driver, even the CPU speed in dianosi. couldn't move at all. I think JNC-40M couldn't work well with Mach3 either their driver or control board problem.
I couldn<t believe that the maker keep telling me tested.......
Alex.

2
General Mach Discussion / Re: Jog not working?
« on: June 20, 2013, 12:44:29 PM »
Hi Hood,
I did Ref All Home, the Z axis motor turn a bit then stop, after that I cut off home sensor manually On/Off  to ZXY axis accordingly.
Then the Zero button of ZXY axis turn to green, mean home completed.
Is it mean the JNC-40M control card or driver setting problem, lost the way....  ???
he driver default setting was Microstep 8, Step/rev 1600, half step, RMS current 2.36A.
I did the auto calibration for XYZ and tested with Jog step mode to confirm the right resolution.
However, the stupid cnc still couldn't do continue jog and home mode.

Note:JNC-40M manual over 6000kb failure send out....

Best regard.
Alex

3
General Mach Discussion / Re: Jog not working?
« on: June 19, 2013, 10:11:57 PM »
 ??? Hi, Hood appreciated. Here i attached the xml file. I am using the JNC-40M came together with the cnc desktop machine. At the moment the maker cannot support how to solve it. Now stall there cannot do the Ref All Home... The stepping motor seem like ok, when i load the gcode go into mach3, machine did run XYZ axis movemenet according to gcode. However, i couldn't continue it without doing Ref All to Home. And the continue Joy also cannot run properly as well.  :'(
Really hope Hood can gave advice...... Thanks.

4
General Mach Discussion / Re: Jog not working?
« on: June 19, 2013, 03:34:13 AM »
Dear hood, i am newbie in cnc. My new bought cnc jog key can move fine in step mode, but not in Jog continue mode. When i click Jog continue for any axis motor just turn a bit. If i keep press hold the Jog key, still same move once only. Look like inching movement, when i do it offline the mach3 run well with continue increase the position. This was happen in ref all home too, only Z axis move a bit then hang up there, need to press Emergency stop to reset. Hope to get the mach prof. advice..... Thank you.

5
General Mach Discussion / Re: JNC-40M configuration?
« on: June 15, 2013, 02:18:22 AM »
hi fabrun i bought it around us 250 in aliexpress, need to check back the history link...thanks

6
General Mach Discussion / Re: JNC-40M configuration?
« on: June 15, 2013, 01:34:30 AM »
HI fabrun, the link i download the software before, i installed successfully. However device manger still shown the yellow color. When update hardware driver again,
windows shown an error that software corrupted.....

7
General Mach Discussion / Re: JNC-40M configuration?
« on: June 15, 2013, 01:29:28 AM »
Hi, thanks for ur inform. i bought it from china online IT tech.

8
hi, iam new in cnc anyone have PLCX 6045M JNC-40M Usb driver support windows 8? i have been post in jnc-40m configuration thread, if this is double post sorry about it.
please send the driver to me alexcfw73@yahoo.co.jp need it urgently to test my first machine. thanks.

9
General Mach Discussion / Re: JNC-40M configuration?
« on: June 14, 2013, 10:18:57 PM »
hi, i'm new in cnc and starting to learn from now on..... i just bought a jnc-40m engrave cnc board one week ago. however i failed to install the jamen usb driver into my new computer asus used windows 8. the device mgner shown the yellow color. i search around the web, couldn't get any inform. for windows 8. May i know anyone have this  latest jnc-40m driver? i couldn't find their official web to download the driver too. if anyone can help me in this issue really appreciated. please e-mail me the driver to alexcfw73@yahoo.co.jp  thanks.

Pages: 1