Hello Guest it is December 01, 2020, 12:57:21 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Jim P

Pages: 1 2 3 »
1
Mach3 under Vista / Re: 32 bit win 7
« on: July 20, 2014, 04:34:19 PM »
Thanks joeaverage for the info

2
Mach3 under Vista / Re: 32 bit win 7
« on: July 15, 2014, 03:41:26 AM »
tweakie, My response to your message ....... Doh! I don' know why the thought didn't occur to me. Old age I guess. LOL

Craig. For some reason I was under the impression that Win 7 platforms wouldn't run Mach3. Don't know where I got that either.

3
Mach3 under Vista / Re: 32 bit win 7
« on: June 28, 2014, 01:54:57 AM »
Just trying to take care of what I think is going to end up being a dead HD and the problems I might run into reinstalling every thing on the new HD. Not sure if I could find all the drivers I need. Not exactly sure what the discontinued support by MS will do to me trying to reload them.


4
Mach3 under Vista / 32 bit win 7
« on: June 21, 2014, 04:41:13 PM »
I've looked and not found a specific answer to my question. seems everyone is looking for the 64 bit answer. I down graded the win 7 I had to XP and installed a P port card. Can I go to a win 7 32 Bit and still have the Mach3 work as it does now. I don't use the PC for anything other than Mach3, solitaire and a big calculator. No internet connection. I hear a rough noise from the HD after its been running for a couple of hours so I'm sure a new HD is in the future and thought I'd go with win 7. I'm not sure there is a reason to drop XP other than the hype of your computer will explode if you keep XP on it. Should I just leave it as is. It works fine. Well, with the exception I will need a new HD sooner or later. So I guess my real question is if XP in its current config will work fine after a new HD should I even worry about win 7?

5
General Mach Discussion / Re: probe inside
« on: June 28, 2013, 09:51:31 AM »
thanks a ton. i downloaded the files last night.
Jim

6
General Mach Discussion / Re: probe inside
« on: June 27, 2013, 03:22:46 PM »
I just did a search with every concievable combination of Interior probing array and could not find it. The only thing i found was the find center of a circle on the x axis. its not a circle. I'll keep searching.

7
General Mach Discussion / Re: probe inside
« on: June 27, 2013, 03:03:22 PM »
I looked at that, I thought it was doing something else. I'll try it out. thanks for the suggestion.

8
General Mach Discussion / probe inside
« on: June 27, 2013, 12:49:22 PM »
I have been looking for a macro to probe the inside of an object in x and y only. i know there is one user that is working on something like that but the last post I found he was off to work out the bugs. Can someone point me in the right direction. it would be used to......... say you have a box with an irregular shape and you wanted to cut a lid for it with a piece that actually slid into the box. I might not have phrased my search right but after looking for a couple of days I can not find anything. I looked in the tool box anddid may searches with multiple key words.
Jim

9
General Mach Discussion / Re: trim pot adjust
« on: May 26, 2013, 03:20:42 PM »
 thanks. we had a windy day kick up yesterday and everytime that happens I get a sinus infection. need to wear a respirator all the time I guess. LOL

10
General Mach Discussion / Re: trim pot adjust
« on: May 26, 2013, 03:00:00 PM »
I am coming down with some bug and am definately not running on all  8 cylinders. however even when feeling great I still cant keep up with you guys. LOL. Anyway my native units is in inches. Brett thanks for all the help but I am lost here. Is .5 inches per minute the same as 2 revs per second?

Pages: 1 2 3 »