Hello Guest it is November 25, 2020, 05:43:18 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - BOATDUDEGUY

Pages: 1 2 3 4 5 »
1
General Mach Discussion / Re: SAVING WORK LOCATION
« on: February 20, 2014, 03:12:03 PM »
thats exactly what i was talking about doing, centering then turning off

im really not that mechanically inclined of a person, perhaps if i had the time but i remember for weeks i was researching machine building and im just not up for it,machines not going to be moving hardly at all off x and y anyways this machines just going to cut wax ring models

2
General Mach Discussion / Re: SAVING WORK LOCATION
« on: February 20, 2014, 02:23:54 PM »
those are nice but i dont know how to install and them and all that
anyways looks like it is what i was affraid of

ill just make it go x n y 0 then turn it off, it doesnt gotta be within microns, its for milling wax so just gotta be in the center of stock and ill be happy

3
General Mach Discussion / SAVING WORK LOCATION
« on: February 20, 2014, 12:32:05 PM »
once i set my work in the middle of my vice or chuck, can i save that location
because the last time i used it i had to find the x and y each time i turned on mach, is there a way other than just once i find it move away say in x4. and y4. and just remeber and move that much once i turn it back on
same for tool zs

is there a way or must i find my work and tool zero each time i boot up mach

thanks in advance

4
General Mach Discussion / Re: 5AXIS
« on: January 22, 2014, 03:24:14 PM »
as ive stated in the past
you the man
thanks again

5
General Mach Discussion / Re: 5AXIS
« on: January 22, 2014, 02:49:20 PM »
The version I use  is 057 but others say 062 is also ok.
Regards tuning, it will all depend on the hardware but basically if they are rotary axes then instead of steps per mm or inch you will use steps per degree.

Hood

this site is different than last i checked here
where can i find that version you mentioned because all i seen on the site was 43

6
General Mach Discussion / 5AXIS
« on: January 22, 2014, 07:32:37 AM »
Hello back again i emailed and asked if the license i previously paid for would be good for 5 axis, they said it would
sooooo
back when i set up my first 3 axis machine there was a specific version, not much older, but not the newest version of mach3 that would run without bug issues

does anyone know of a specific mach i should download for the chinese 5 axis engraver im buying

also can anyone give me advice on how you would go about tuning the 4th and 5th axis motors, cause ive got no clue

thanks in advance for any and all advice

7
General Mach Discussion / WORK/ TOOL OFFSETS
« on: September 24, 2012, 06:40:11 PM »
HOW DO I SAVE THEM?

8
General Mach Discussion / Houston tx DIY`ERS/HOBBYISTS
« on: July 29, 2012, 07:36:38 PM »
hi my name is richard im looking for diyers/ hobby machinists to hang and go over software, and machining
help each with troubleshooting and learn what ever i can from you and vice versa
ive got the 3020 cnc
type that in on ebay
and a harbor freight lathe i plan on converting to cnc in the near future

ive got vectirc aspire,autocad,mastercam,and mach3
reply or message if your in my area and interested

9
General Mach Discussion / Re: offsets
« on: July 29, 2012, 07:04:04 PM »
well ya when i specify cutter comp on mastercam for wear it alwasy puts itin

i dont manually program anymore
its great to know how to be able to see whats going to happen before hand
but ive been spoiled by cadcam

10
General Mach Discussion / Re: offsets
« on: July 29, 2012, 06:05:13 PM »
ah okay so in the tool table is where you make the offsets thanks hal

Pages: 1 2 3 4 5 »