Hello Guest it is March 29, 2024, 07:40:29 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - eliasagrio

Pages: 1 2 »
1
VB and the development of wizards / Re: Tool zeroing macro help
« on: December 25, 2013, 10:55:16 AM »
well,  I copy the script to the autozero tool button and saved but when tried to use it nothing happened other than a line appearing in the status bar with "script line error "  message.
by the way      MERRY CHRISTMAS!!!!!!!

2
VB and the development of wizards / Re: Tool zeroing macro help
« on: December 24, 2013, 07:53:57 PM »
nope. it  did not work  bro.   any other solution?

3
VB and the development of wizards / Re: Tool zeroing macro help
« on: November 26, 2013, 03:41:13 PM »
uhhhhhhhf

4
VB and the development of wizards / Re: Tool zeroing macro help
« on: November 26, 2013, 08:19:07 AM »
Jackson, Nj and yourself?

5
VB and the development of wizards / Re: Tool zeroing macro help
« on: November 25, 2013, 11:50:58 PM »
hey man!!!!!!  I really appreciate your help.  so far, I have not been able to try the las one you sent me due to my job dedication, I work on an adult community and have no help and because of the fall clean ups  most of my time is taken by that; hopefully by the winters' first weeks I will Have a chance to go back to it and I promise I'll keep you posted.


BEST REGARDS:

Elias Agredo

6
VB and the development of wizards / Re: Tool zeroing macro help
« on: November 18, 2013, 01:32:31 PM »
IT IS ATTACHED TO A BUTTON. THE AUTOZERO ONE

7
VB and the development of wizards / Re: Tool zeroing macro help
« on: November 18, 2013, 08:24:57 AM »
ohhh, and also I must mention that I have taken my cnc all apart to rebuilded which is now completed however, I'am 100% sure everything was connected in the same way I originally built it meaning that all the pin #s outputs and inputs are the same as in the former cnc.

thanks and
Godspeed

8
VB and the development of wizards / Re: Tool zeroing macro help
« on: November 18, 2013, 08:20:22 AM »
doesn't do anything at all but an script error appears in the status line.
as always!!!!!  thanks a million in advance
 Godspeed

9
VB and the development of wizards / Re: Tool zeroing macro help
« on: November 17, 2013, 05:30:18 PM »
hey JohnHaine, thanks so much for your prompt help, I did no answer earlier because I have been too busy at work but anyway.
yes I have tested  and double checked the probe and is working fine, the pin light illuminates when touching the probe to my bit.  this is the original script I was using and the second one I have tried after the first one stop working but also without any positive outcome.
Message ( "Auto zeroing...:)
If  IsSuchSignal (22)Then
code "G31 Z-3 F20"
While IsMoving()
Wend
Call SetDRO( 2, .125)
code "G1 Z1"
End If

and the second one

PlateThickness =GetUserDRO (.125)
If GetOeled (825)<>0 Then
DoOEMButton (1010)
Code "G4 P5"
Code G31 Z-.75 F10"
While IsMoving()
Wend
ZProbePos =GetVar(2002)
Code"G0 Z" &ZProbepos
While IsMoving()
Wend
Call SetDro (.125)
Code "G4 P0. 125"
Code "G0 Z1"
Code"(Z axis is now zeroed)"
Code "(Z-Plate is grounded, check connection and try again)"


I hope that you can help with a good one.   and thanks a million in advance

good luck

10
VB and the development of wizards / Re: Tool zeroing macro help
« on: November 01, 2013, 05:47:09 PM »
Hello Everyone!!!!
a newbine  here. please help with  script for Autozeroing. my touch plate is .1250 inc.  it was working fine but suddenly stop working now I can't autozero. I thanks a million in advance.

Pages: 1 2 »