Hello Guest it is March 28, 2024, 02:11:36 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Algec

Pages: 1 2 3 »
1
General Mach Discussion / Re: REF ALL HOME problems with 4º Axe
« on: August 25, 2012, 06:49:59 AM »
THis is my configuration file. Thank you very much

2
General Mach Discussion / Re: REF ALL HOME problems with 4º Axe
« on: August 24, 2012, 07:18:58 PM »
I havent limit switch in my 4º axe, but I have this input disabled.I only have enabled the step and dir pins, and when I do this REF ALL HOME dont finish the job. Where is the task of this order, is a G code order? Maybe a macro?

3
General Mach Discussion / REF ALL HOME problems with 4º Axe
« on: August 24, 2012, 08:00:05 AM »
I have a problem with task of make the zero machine ajust.
 It task always worked well, but since I "put on" the 4th axis,it does all the work.
 If I push REF ALL HOME, MAch3 move the X, Y and Z and light green LEDs indicating which are indexed when each axis touch the limits switch , but when this three axes finish, all the leds greens turn red and dont are ready for use software limits.
 The lEDs of all axes is now red and I'm not willing that the machine coordinates are well referenced.
 The 4th axis is rotary.
 If I remove the 4th axis use,this task work fine again. Make same and when Z Axe touch limit switchs all leds tare green and I can use software limits
 I dont know where indicate to Mach3 that the 4th axis must not make the process of resetting the machine coordinate. Can anyone help?
Why this happend?
Excuse my bad english

4
Brains Development / Problems with brain, modbus and MPG
« on: July 28, 2012, 08:22:02 AM »
I use a brain with a modbus /RS232 and MPG
My problem is my MPG slide each axe with no selection of direction and speed.
MPG work ok , the program into the Modbus it is checked and is ok but I think brain maybe bad, please can you check it and say me how can I do for my MPG work ok?
All Modbus is working good.
This is a card who make a friend, Siliconio, and all is checjker and work ok
I paste the brain for you can watch and say me...
Excuse my bad english

5
Spanish / Re: Puede Mach3 usar mas de un plugin de comunicacion???
« on: March 19, 2012, 04:18:15 PM »
Pienso que si si estan bien configurados. EL mach es muy flexible. Yo uso paralelo y serie a la vez como es logico, con plugings y brains, y dos plugins seguro se pueden ejecutar a la vez en mach, ahora que no se si habria conflictos en los hard.

6
Spanish / Re: Puede Mach3 usar mas de un plugin de comunicacion???
« on: March 19, 2012, 02:35:18 PM »
Creo que si pero no se me ha dado el caso de hacerlo,
Que pluging ethernet?

7
Spanish / Re: control de consumo en motor, se puede hacer?
« on: March 10, 2012, 08:37:58 AM »
Lo unico que se me ocurre es montar encoders y habria que hacer un circuito que comparara la cantidad de pulsos que van a las controladoras y los de realimentacion de los encoders, Si la diferencia ens mayor de..... habria que generar una parada de emergencia.
El problema de mach3 y es que no usa encoders, es de lazo abierto y supone que lo que pides lo hace. Eso obliga a usar motores sobredimensionados y corres ese riesgo. No se quema nada solo estropeas la pieza y puedes romper una fresa (me ha pasado varias veces).
Los encoders son caros  aunque podrias hacer algo mas simple con un contador por vuelta del husillo con un fotoacoplador tipo limit swith y un contador que cuente los pulsos por vuelta y sea puesto a cero con el fotoacoplador. Si el error es mayor de una vuelta de husillo ( o partes de este si pones una pequeña rueda de segmentos en el eje) generr una parada de emergencia.
Eso es hacer un encoder casero con un limitswith optico y un disco dentado pequeño. No es muy complicado y si seria mas barato. Quizas cueste todo unas horas de trabajo y lo que vale una buena fresa. 20E o 30
Espero haberlo explicado bien.
Si tienes dudas dimelo y te mando alguna ayuda mas.

8
Spanish / Re: control de consumo en motor, se puede hacer?
« on: March 10, 2012, 06:45:30 AM »
no se quema, el motor paso a paso consume lo mismo tanto si se mueve como si no, olvida los conceptos que tienes de motores ac y dc convencionales, esto fubciona de otra forma,

9
Spanish / Re: control de consumo en motor, se puede hacer?
« on: March 09, 2012, 02:09:19 PM »
LOs PAP consumen lo mismo independientemente del par que les pidas, asi que no necesitas nada de eso.
Estan ajustados en corriente y suben a la I maxima todo el tiempo.
Si quieres por seguridad pon fusibles en ambos pero insisto no lo necesitas para nada

10
Spanish / Re: Step pulse / Dir pulse
« on: February 26, 2012, 04:29:39 AM »
El kernel dejalo en lo mas bajo, si lo subes mucho, depende del hardware del pc, puede funcionar mal.
Cuando la tengas bien controlada puedes probar subiendo de paso en paso al siguiente escalon y probar.
Afecta a velocidades añtas d ela maquina.
Quita todo lo que este resiedente en el pc de programas , hasta el antivirus si puedes y vuelve a probar.

Pages: 1 2 3 »