Messages

1

SmoothStepper USB / Re: New ess install, can not get smooth stepper to write to XML

« on: October 07, 2012, 09:07:32 PM »

It is working!!!!

Used mach ver 062, third of latest version of ESS driver. It did not save the changes to the XML at fiirst. Changed mp3 in mach3 to run as xp, when asked to use the default after entering the IP addrerss during the mach3 startup

 I said yes, the default loaded and I could save to the XML. I can make changes now with no problems, System is now cutting parts!


Thanks,

Frank

2

SmoothStepper USB / Re: New ess install, can not get smooth stepper to write to XML

« on: October 06, 2012, 11:41:15 PM »

Thanks Jeff, I downloaded the (062) and will try tomorrow,

3

SmoothStepper USB / New ess install, can not get smooth stepper to write to XML

« on: October 06, 2012, 08:46:57 PM »

Back Ground: Old computer finally kicked the bucket (xp system with mach3 parallel port setup no ss, served me well for 6 years) Have new computer running win 7 32bit, installed new ess.

I have loaded the latest mach3 (066), and ess V10fb2 driver. ran through the normal setup and cannot get the plugin to right any changes to the XML file (when I restart mach3 it is like a fresh install). Checked for read only conditions on XML already.

Questions;

1.  Does the ESS hardware have to be installed and connected in order to write to the XML file?

2. When you make changes to the ss pugin config in mach3 does it actually write code in the xml or somewhere else?

3. Any suggestions ?

4

General Mach Discussion / Re: jog issue, please help

« on: September 28, 2011, 05:41:49 PM »

spent the day cutting. tried different accels, and exact stop mode. Both would solve the issue but cause other issues when cutting at high speeds.

Going to think about it for awhile.

Frank

5

General Mach Discussion / Re: jog issue, please help

« on: September 28, 2011, 10:45:38 AM »

Hood, thanks for the input. I'll try what you mentioned.


Frank

6

General Mach Discussion / Re: jog issue, please help

« on: September 27, 2011, 07:08:47 PM »

Attached is the file

Thanks for your help!

Frank

7

General Mach Discussion / Re: jog issue, please help

« on: September 27, 2011, 06:37:31 PM »

no message.

ran some more tests. works correctly with a G0 command but not with the G1 command

Frank

8

General Mach Discussion / jog issue, please help

« on: September 27, 2011, 05:27:13 PM »

First time post,

Back Ground. CNC DIY router table 10ft x 4ft x 2.5ft using 34 steppers and ball screws with porter cable head. Mach3 software. Been using it for about 4 years typically at 100ipm. Need more speed so we upgraded to rack and pinion on all axis. (2 to1 belt reduction, 1" pitch dia and 8x micro step). Wow what a difference. Now able to see up to 1000ipm. System working smoothly and repeatable on all individual axis testing.

ISSUE: when I request more than one axis command the next command starts before the first one is finished.

example:

f500
x40
z1
z0

At approx 39" z starts to 1", at 40 " z is back to 0. x actually measures 40" and mach3 screen does show z starting up around 39" (may be lag not sure)
@ 100ipm i do not see this. may have always had the issue just never ran these speeds before.

Tried different accel speeds and kernel speeds no change.

thanks in advance for your help