Hello Guest it is February 06, 2023, 04:53:51 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dude1

1
What they have in them, (you will need to read the recent changes and compare that to other posts) machine definitions (beta) is the biggest one that is in the newest Mach3 post, not all post are kept up to date Mach3 is.

2
Use the one from the default postprocessor location (use installed post libaray), it is up to date and it already has the A axis set up in it, you just have to set if it is long X or along Y axis

3
General Mach Discussion / G17
« on: February 13, 2019, 01:23:24 AM »
Is it ok for mach3 to have a G17 on a line by itself as it is at the end of the Gcode below?

Code: [Select]
(1001)
(SPOONS X 2 ORIGIN ON FROUNT SET)
(POST PROG )
(GENERATED ON WEDNESDAY, FEBRUARY 13, 2019 192159)
(T3  D=12.7 CR=0. - ZMIN=0. - FLAT END MILL)
G90 G94 G91.1 G40 G49 G17
G21
G28 G91 Z0.
G90

(FACE1)
M5
M9
T3 M6
S18000 M3
G54
G0 X375. Y-38.857
G43 Z11. H3
Z6.
G1 Z1.27 F700.
G18 G3 X373.73 Z0. I-1.27 K0.
G1 X366.75
X126.75 F1250.
X119.75
X-120.25
X-127.25
X-367.25
G17 G2 Y-27.968 I0. J5.444
G1 X-127.25
X-120.25
X119.75
X126.75
X366.75
G3 Y-17.08 I0. J5.444
G1 X126.75
X119.75
X-120.25
X-127.25
X-367.25
G2 Y-6.191 I0. J5.444
G1 X-360.063
X-127.25
G3 Y4.697 I0. J5.444
G1 X-131.796
X-366.733
X-366.75
G2 Y15.586 I0. J5.444
G1 X-126.872
G18 G2 X-125.602 Z1.27 I0. K1.27 F900.
G0 Z6.
X-117.266 Y-6.191
G1 Z1.27 F700.
G2 X-115.996 Z0. I1.27 K0.
G1 X-113.063
X119.75 F1250.
G17 G3 Y4.697 I0. J5.444
G1 X115.204
X-119.733
X-119.75
G2 Y15.586 I0. J5.444
G1 X120.128
G18 G2 X121.398 Z1.27 I0. K1.27 F900.
G0 Z6.
X129.734 Y-6.191
G1 Z1.27 F700.
G2 X131.004 Z0. I1.27 K0.
G1 X133.937
X366.75 F1250.
G17 G3 Y4.697 I0. J5.444
G1 X362.204
X127.267
X127.25
G2 Y15.586 I0. J5.444
G1 X367.128
X367.25
G3 Y26.474 I0. J5.444
G1 X127.25
X120.25
X-119.75
X-126.75
X-366.75
G2 Y37.363 I0. J5.444
G1 X-126.75
X-119.75
X120.25
X127.25
X367.25
G18 G2 X368.52 Z1.27 I0. K1.27 F900.
G0 Z11.
G17

G28 G91 Z0.
G90
G28 G91 X0. Y0.
G90
M30

4
General Mach Discussion / Re: fusion 360 mach3 turn atc g28 stops
« on: August 27, 2018, 02:06:23 AM »
Is there a M0 after the G28 this is the same as the answer you got on the fusion forum.

5
Ask in here you will get a better answer than what you got on the fusion forum https://www.facebook.com/groups/fusion360users/

6
PoKeys / Re: Pokeys 57E + Mach4 + Lathe / Turning Application
« on: July 15, 2018, 04:10:52 PM »
The 57cnc has been used to control a lathe, ttps://blog.poscope.com/encoder-threading-mach4-lathe-usb-cnc-controller-pokeys57cnc/ the 57e has in it's data sheet that it can be use with a encoder, have you directly asked the pokeys guys.

9
you can use your keyboard num pad, I tried it a few years ago and it worked

10
PoKeys / Re: I need help setting up my mach4
« on: June 24, 2018, 01:16:06 AM »
With the pokeys you don't realy do a lot if it is working as intended in pokeys config what is not to be relied on it is just a guide.

When you first boot up Mach4 just go through the steps it say to do in the config then ounces that is done reboot mach 4 and the pokeys board. then when you start mach 4 again confirm the pokeys board then just look at the settings to make sure they are correct if not go into the pokeys config to change it there, and restart mach 4 and the pokeys between big setting changes. you have to be careful when setting up any of the pokeys boards that you do not change anything for a start in mach 4 the pokeys does most of it for you.   
The first time I set up a 57cnc it took a week of doing the wrong thing then an hour reinstalling mach 4 then letting pokeys set mach 4 up, it is the same with mach3.

You may need to start again.