Hello Guest it is March 28, 2024, 05:06:53 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - matos67

Pages: 1
1
Hi Crack123 ,
To solve my problems i installed Mach3 R3.043.022 + pokeys 10.4 plugin.Since it is working perfect!
Pokeys plugin attached to this message. Tell us if it works for you.
Mathieu

2
PoKeys / Re: Mach only see's inputs when pockey software is running.
« on: April 30, 2011, 01:57:23 PM »
Hi Tom,
Here is my email adress: fastmp@sfr.fr
Thanks a lot.

Mathieu

3
PoKeys / Re: Mach only see's inputs when pockey software is running.
« on: April 30, 2011, 03:10:05 AM »
Hi Tom,
I mean the Pokeys software for programming the pokey! I would like tro try the plugin 10.4 but can't find it to download.Do you have a copy of this file?
Thanks Mat.

4
PoKeys / Re: Mach only see's inputs when pockey software is running.
« on: April 28, 2011, 06:36:36 PM »
Seems my problem comes from a conflict between smoothstepper and pokeys.When i run mach3 without the smoothstepper plugin activated pokey works perfect. When smoothstepper pligun is activ pokeys only works with the pokeys software running in the background. And then it does in slow motion. Someone to give me a tip?
Thank you
Mat

5
PoKeys / Re: Mach only see's inputs when pockey software is running.
« on: April 28, 2011, 01:36:12 PM »
Hi tom
When you choose a terminator, click on DRO's then type 223 in the box called "select mach3 DRO value to use". code 223 is NOT in the present choice list. There are several other OEM DRO codes you can find in the wiki but not in the choice list of the brain editor.
Mat

6
PoKeys / Re: Mach only see's inputs when pockey software is running.
« on: April 28, 2011, 08:35:56 AM »
Sorry Tom i made changes in the wrong file. And did no try it on my machine cause i use two separate pots.
The terminator 223 stands for OEM DRO code 223- rapid override. You can find these codes under this link:

http://www.machsupport.com/MachCustomizeWiki/index.php?title=OEM_DROs

By the way i rewrote the brain. Tell me if works.

Mat

7
PoKeys / Re: Mach only see's inputs when pockey software is running.
« on: April 28, 2011, 06:10:23 AM »
Hi thosj,
Try the attached brain it should work for you.

Mat

8
PoKeys / Re: Mach only see's inputs when pockey software is running.
« on: April 27, 2011, 05:52:05 PM »
Hi thosj,
I tried several versions of mach and had always the same issues. The more reliable at the moment is 035, it gives me good results with the analog inputs. With 022 i had problems with FRO, it was erratic in following the analog signal.Concerning your problem i'm quite sure you are using a brain to round the FRO to 100% when it gets between 98% and 102%. This brain can be found in this forum and is called FRO100.brn. It works with Mach 022 but no 035. Seems the way mach reads brains have been modified in some way.So i wrote a new brain that  works with mach 035. In this new version the fro reset is done AFTER the analog switch has gone to 0. Go in mach3/brains and replace FRO100.brn or equivalent with newFRO100.brn. Then launch mach 035 go in "operator">"brain control" then click "reload all brains" , select newFRO100 and tic enable. Brain is attached to the mail. Hope it helps you.

Mat

9
PoKeys / Mach only see's inputs when pockey software is running.
« on: April 27, 2011, 09:51:21 AM »
Hi,

I'm using pockey to connect a control panel on a retrofitted mill to mach3.
I use pots for feedrate override, spindle speed,push buttons for manual spindle cw ccw, and so on.
Everything works fine BUT very slowly. It takes 2 or 3 seconds to read a digital input also for analog. Another problem is mach will read the inputs only if the pokey software is running.
I run a pc that is only dedicaded to mach3, with smoothstepper , shuttlepro and pokeys as plugins.
Neddless to say i use latest versions of plugins and softwares.
Would be very nice if somebody could help.
Thank you

Mat.

Pages: 1