Hello Guest it is March 19, 2024, 01:21:05 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sebba

Pages: 1 2 3 4 5 »
1
Mach Screens / Re: Saving Button Script - .set or .m1s?
« on: May 21, 2020, 03:05:20 AM »
.mcc files are compiles lua chunks and are applicable in Mach4 only.

I am not so sure... I have .mcc files in my Mach3, also (compiled m1s scripts)

2
install Mach3 and run VB Script Editor from Operator menu

3
thanks for your reply
I thought there is some more "elegant" solution  :)


4
Hello,

There is any way to get the last pressed button's code and place it into macro as variable?
For Mach3.

Thank you,
Seb

5
Mach Screens / Saving Button Script - .set or .m1s?
« on: March 27, 2020, 06:20:15 AM »
Hello,

Sorry if this question was covered but I was not able to find the answer...

My question is: which way is better? to leave the button's code in screenset .set file or to save it in .m1s file?
I care about that for a large number of buttons with scripts, not for a few...
Mach3 will run slower if scripts will be saved in .set file? Any improvements if scripts are saved in m1s files?
Screenset loading process is affected, too?

I'm thinking the loading of screenset will be faster if scripts will be saved in m1s files but I don't know if entire application will run faster or not.
Any advice is welcome

Thank you,
Seb

6
VB and the development of wizards / Re: Mach3 CB timers()
« on: June 04, 2015, 02:06:33 AM »
thanks for your reply

but... I don't get a value in milisecs...
GetTimer return a value of 3.0yyyy for an interval of 33 seconds

Quote
Thu - 09:03:47 ---Wait for spindle to reach the requested speed... 0
Thu - 09:04:20 ---Spindle Error! Requested Speed Not Aquired!! Program Execution Aborted! - Line: 9 - 3.02204

7
VB and the development of wizards / Re: Mach3 CB timers()
« on: May 31, 2015, 04:30:01 AM »
hello,

I'm getting similar values from GetTimer(xx), not seconds...
What was the problem?

Thanks

8
General Mach Discussion / Re: Mach3 and UHU Servo controller
« on: March 09, 2015, 01:46:01 PM »
of course! :)

I just placed the order, hope I'll have the parcel with no delay! :)

9
General Mach Discussion / Re: Mach3 and UHU Servo controller
« on: March 08, 2015, 11:50:37 AM »
Thanks for your input, Hood
I just contacted the guy who sell this device: http://bukovinskygroup.com/catalog/product_info.php?products_id=29
And he told me this device will do the job

I think I'll order one to test it... :)

Regards,
Seb

10
General Mach Discussion / Re: Mach3 and UHU Servo controller
« on: March 08, 2015, 06:46:02 AM »
Hello.... after 8 years... :D

So, better late than never...  I have to work with AC servos for now... :)
In fact, I have some OSAI OSS-200 drivers and S-4030 motors and - like a big (old) boy - I want to play with them :)
But - as you can easily guess - this play should be managed by Mach3

After some research, I found this UHU servocontroller and I'm wondering if I can find someone with more experience with these devices and who can share his's experience and results, pros/cons reasons etc

thanks,
Seb

Pages: 1 2 3 4 5 »