Hello Guest it is September 29, 2020, 05:51:30 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Hermie

Pages: 1 2 »
1
VB and the development of wizards / Re: Tracing an object
« on: February 27, 2018, 01:49:22 PM »
Thank you sir, this will save me a lot of time and tree carcasses.

2
VB and the development of wizards / Tracing an object
« on: February 26, 2018, 06:12:09 PM »
I am having a problem with a small bit of code and am hoping someone can help me.
I have some special maple and yew burls and slabs I need to trace so I mount one on the table and trace it using the
crosshairs in the video window. Until now I have been writing the dros down on paper and inputting them into Aspire
by hand.
That was ok before but now I have been given 5 more to do, so with your help, I would like to use a button to
record the dro to a file so I can speed things up a bit.
So far I have gotten the code into the button and it writes to the file but when I try to write the next line to the
file it overwrites the last line, could someone please have a look and tell me what I am missing?

   
Sub Main ()
Open "L:\test\TESTFILE.txt" For Output As #1 ' Open to write file.


   X = GetOEMDRO (800)
   Y = GetOEMDRO (801)
   Z = GetOEMDRO (802)


Write #1, X, Y, Z

Close #1

End Sub               


With many thanks; Herman

3
General Mach Discussion / Re: Spindle Controls
« on: April 13, 2015, 10:01:11 AM »
Aspire has a post processor editor that will allow you to edit your Mach processor, I haven't had to use it for a while but the instructions to insert an M call is well documented on the Vectric website.

4
General Mach Discussion / Re: 3D printing with Mach 3
« on: April 13, 2014, 10:39:46 AM »
Gary,
I've been trying to set up my cnc for printing too, and as far as I can tell Simplify and Replicator and the other slicing programs define the extruder as "E" axis, so all I did is start a seperate profile in Mach and renamed E to A in the g code, the -1 and +1 you see are a retraction or feed of + or - 1 unit to prevent the plastic from drooling, so you don't get little strings of material every time it lifts the hot end. So far so good, now all I have to do is figure out the PID temperature controller.

5
General Mach Discussion / Re: unwanted creep in jog mode?
« on: November 25, 2013, 09:31:59 AM »
Ive been using version 62 for about a year it seems fairly stable. I reused the xml in my backup. Nothing changed on the machine so there was no need to change anything in the settings. The only thing I changed was turning off the wi-fi connection so windows wouldnt update and mess with the settings.
Herman

6
General Mach Discussion / Re: unwanted creep in jog mode?
« on: November 24, 2013, 01:11:51 PM »
I had the same problem with my xml getting wiped, turned out to be, in my case, a windows problem, caused by a corrupt registry. Just a thought :)

7
G-Code, CAD, and CAM discussions / Re: 4 axis mill 3D model software
« on: September 07, 2013, 02:14:27 PM »
Try vectric cut 3d, good program for 3d stuff. Try a free trial and see if you like it.

8
General Mach Discussion / Re: Can't get 2.2KW spindle to work
« on: June 04, 2013, 05:45:08 PM »
 :)

9
General Mach Discussion / Re: Can't get 2.2KW spindle to work
« on: June 04, 2013, 04:52:50 PM »
sorry to interject, and correct me if I'm wrong but it looks like he has it set for analog speed control PWM output is kitty corner on the board

10
Third party software and hardware support forums. / Re: corelcad
« on: October 15, 2012, 04:07:34 PM »
Hi Ive been using it for about a year, it is basically an autocad Knock off but with a lot less features, Im no expert by any stretch of the imagination but my brother ( a draftsman) likes it and after trying a few other programs I settled on corelcad because of the relatively low price and ease of use.

                                                                                               Hermie

Pages: 1 2 »