Messages

1

Works in progress / Re: New IPS (Interactive Programming System) Professional Screen for Turn

« on: September 10, 2011, 05:45:02 PM »

wes i would like to test your program
please send me a copy of everything i would need
I have a hobby cnc lathe and mill
I use them everyday
thanks JuMpS4
the pics are of a model I have been working on ( Yulee Sugar Mill ), the roller mill is the only parts i have used cnc on

2

Works in progress / Re: 3 PAGE LATHE SCREEN - WIZARD ADDITIONS

« on: September 10, 2011, 05:12:24 PM »

the pics i sent are a model of the yulee sugar mill
thanks again

3

Works in progress / Re: 3 PAGE LATHE SCREEN - WIZARD ADDITIONS

« on: September 10, 2011, 05:08:10 PM »

Rich or anyone else please help me locate the newest lathe wizards and their screens i have searched my brain numb
i understand they are all or most in beta and  i would like to test them.
finding the complete setups in a zip is killing me  lol
i'm interested in the 3 page lathe screen wizards very much and anything else
i can help test i use my hobby cnc lathe and mill every day
any wizards for mill would be nice also
thanks
attached is my work in progress pics I'm a serious mach3 user and would thank anyone for any help

4

Works in progress / Re: THE LATHE PROJECT-2011 - WIZARDS SCREENS ONLY

« on: June 13, 2011, 06:50:30 PM »

hi where do i find the wizards that go with the "flyout modified hcir.jpg" above. Rich suggested i look at these and they look great i'm just a bit new and confused as to how to add them. I have added a few wizards with sucess they were zipped and like to find this package If I could
thanks steve

5

General Mach Discussion / Re: would like help using mach3turn wizard

« on: June 12, 2011, 08:32:15 PM »

thank you
I made the cutter and the gears I needed worked well
steve

6

General Mach Discussion / Re: would like help using mach3turn wizard

« on: June 11, 2011, 06:46:13 PM »

the article would require a tool for every range to be made myway would be so easy i'm off to find a user wizard that will cut a radius from both directions someone else has to have had this come up.
thanks for your fast reply you guys in here are great
I guess I'm going to have to learn lazyturn too   ....
good thing this is a hobby they would be cutting my pay if this was my living lol
thanks again
steve

7

General Mach Discussion / Re: would like help using mach3turn wizard

« on: June 11, 2011, 05:34:19 PM »

I have just started with cnc and I know no g-code I'm using wizards to start with some really good results. I can make this by making the cut in the middle of a longer shaft doing one side then inverting it in the collet and finishing but I would like a way to cut the radius on the left side without removing the shaft from the collet I purchaced both mach and new fangled products I dont know where to update  I'm new to forums also so I get
lost easy 
thanks for any help   
ps nice job on your fly cutters that looked like it worked well too I did them by hand under a magnifyer  worked ok
this Idea I have should produce a full set of cutters for however many teeth that will last a long time

8

General Mach Discussion / Re: would like help using mach3turn wizard

« on: June 11, 2011, 05:17:49 PM »

the tool then will be milled and relieved to work like a hob but with just one row of teeth

9

General Mach Discussion / Re: would like help using mach3turn wizard

« on: June 11, 2011, 05:14:04 PM »

The txt doc opens in wordpad

10

General Mach Discussion / Re: would like help using mach3turn wizard

« on: June 11, 2011, 05:13:19 PM »

hi rich
thank you for your reply
here is a post i found to make a form cutter for the lathe, I was trying to get the fillet wizard to cut the radius's on the shaft. it cuts the right side as your facing it fine but I cannot cut a radius on the left side.