Messages

1

General Mach Discussion / Re: problem size in mach3

« on: December 17, 2010, 06:07:17 PM »

i did put 1016 per step its working  perfect size  thank very much it is  working 100% thank you .
 

2

General Mach Discussion / Re: problem size in mach3

« on: December 17, 2010, 05:44:12 PM »

sorry all i know u did help me to run my machine in past i have this info it may help again thanks for your advise . steps per 760 .velocity 151.98. Acceleration 4. step pulse0 dir pulse 0 .

3

General Mach Discussion / Re: problem size in mach3

« on: December 17, 2010, 05:35:22 PM »

 the steppers are direct drive. (helical couplers )

  high-precision linear Round rails, diameter 0.8-inch,
     

  The use of high-precision new ball screw, 

there is no rebound in return;  diameter 16 mm; pitch 10 mm;   

  Aluminum alloy T-slot table,  Can help you cut and fixed,
  Manufacture than wood table has a huge advantage,

   NEMA23 stepper motor current is 3A, the weight 2.2 pounds ,Torque 1.7n.m 245 oz.In.

    30v 3A CNC drive,tb6560 , Optical isolation, the maximum 1 / 16 micro-step,Spindle control relay

     400w 30v Switching Power Supply

 spindle motor is  850w, 4 level speed, 5000--30000RPM, Strong power;

  milling tool diameter:  8mm,6mm,3.175mm

Router is the length of 28 inches, width
 thanks  for your  answer

4

General Mach Discussion / Re: problem size in mach3

« on: December 17, 2010, 05:25:17 PM »

no if i command a 1 in  it will be  0.740 . thank hood  for your help.
 T1M6
G0Z1.0000
G0X0.0000Y0.0000S15000M3
G0X0.0163Y0.0198Z1.0000
G1Z-0.0250F9.4
G1X1.0163Y0.0198F14.2
Y1.0198
X0.0163
Y0.0198
G1Z-0.0500F9.4
G1X1.0163Y0.0198F14.2
Y1.0198
X0.0163
Y0.0198
G1Z-0.0750F9.4
G1X1.0163Y0.0198F14.2
Y1.0198
X0.0163
Y0.0198
G1Z-0.1000F9.4
G1X1.0163Y0.0198F14.2
Y1.0198
X0.0163
Y0.0198
G0Z1.0000
G0X0.0000Y0.0000
G0Z1.0000
G0X0Y0
M30

5

General Mach Discussion / problem size in mach3

« on: December 17, 2010, 05:04:15 PM »

hi, can anyone explane please after i put gcode into mach3 itis always reads  wrong size ex if i want square 1in it engraving it gos to  0.940 so i have to  creat square 1.325 in till i get 1 square inch i need your advise please
T1M6
G0Z1.0000
G0X0.0000Y0.0000S15000M3
G0X0.0121Y0.0202Z1.0000
G1Z0.0000F9.4
G1X1.3371Y0.0202F14.2
Y1.3452
X0.0121
Y0.0202
G0Z1.0000
G0X0.0000Y0.0000
G0Z1.0000
G0X0Y0
M30

6

General Mach Discussion / Re: gcode G00 Y -40

« on: November 15, 2010, 06:15:52 PM »

thanks for your answers  i got problem after i put the name into toolpath coz the letter abit small its me i dont know how to chose right tool i will learn but i need more information thanks

7

General Mach Discussion / Re: gcode G00 Y -40

« on: November 14, 2010, 05:26:05 PM »

thanks for reply i typed letter  in artcam  and try to make small  name necklace   and transfer to gcode through artcam and put in mach3  i became very big G00 Y -40  .

8

General Mach Discussion / gcode G00 Y -40

« on: November 14, 2010, 04:42:05 PM »

hi, can anyone help please all my g code start with G00 Y -40  even when iam try to wrihe small name within 2 cm square ?   why gcode go too big G00 Y -40, thank you

9

General Mach Discussion / Re: Feedrate 300% red

« on: November 11, 2010, 11:33:06 AM »

Thanks hood and active member .

10

General Mach Discussion / Feedrate 300% red

« on: November 11, 2010, 11:21:46 AM »

Hi is there any problem if put my machine feedrate 300% red is flashing  when is working I only engraving names 2mm thik silver ? Many Thanks