Hello Guest it is July 02, 2022, 01:40:23 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Csabika

Pages: 1 2 »
1
Machscreen Screen Designer / Re: Changing image file
« on: September 12, 2010, 02:19:00 PM »
Hi Klaus!

I changed the image name, the folder is still standing but it is just a picture in the folder.
Be that, regardless of the name, load the picture in the folder.

regards Csaba

2
Machscreen Screen Designer / Re: Changing image file
« on: September 09, 2010, 05:09:36 AM »
Hi Klaus!

I will stick to the existing setup.

another question
because I change the pictures because this is a picture cut saws
how to do it no matter what the image name is always the one which they fill are in the folder. because they are always changing but there is only one

3
Machscreen Screen Designer / Re: Changing image file
« on: September 08, 2010, 03:58:11 PM »
Hi!

I would like that the Mach screens show me a picture, but the url of  is picture C:\Mach3\Bitmaps!
It is worst to me, i want change the folders, so i can open any picture from your computer.
for example: C:\Desktop\asd.jpg, or D:\Images\asd.jpg!

Can I change this url in the Mach Screen Editor?
Thank you very much!

Hi,
Csaba!

4
VB and the development of wizards / Re: Y, U, V Change X DRO
« on: July 03, 2010, 04:51:14 AM »
Hi KTM!

Attach a G-Code file The X-Y-U-V
probe code
g0 x600
m7m1
x1200
m7m1
x1800
m7m1
y300
m7m1
u600
m7m1
v300
m7m1
m2m30

Hi Csaba

5
VB and the development of wizards / Re: Y, U, V Change X DRO
« on: June 29, 2010, 04:25:25 PM »
Hi!

KTM
I do not see where you are only the cut

Csaba

6
VB and the development of wizards / Re: Y, U, V Change X DRO
« on: June 26, 2010, 09:18:39 AM »
Hi Ian!

I used to be so because the optimizer does the code.

KTM!
The dspmc be because the enginedriver analog + / - 10V

Csaba

7
VB and the development of wizards / Re: Y, U, V Change X DRO
« on: June 25, 2010, 09:44:13 AM »
Someone help please very important.

Csaba

8
VB and the development of wizards / Re: Y, U, V Change X DRO
« on: June 25, 2010, 09:42:53 AM »
Hi Steve!

problem with me using it, motion control DSPMC and can not be given the same number of output shaft.

Regards Csaba

9
VB and the development of wizards / Re: Y, U, V Change X DRO
« on: June 23, 2010, 02:46:49 PM »
Hi Tweakie!


Not.

Any axis is G code, always  move the X axis and XDRO
the code line by line with the movements.
G code: G0 X500      '  move x axis 500mm
                X800      ' move x axis 800mm
             M01
            G0 Y600      ' move x axis 600mm
            M01
            G0 U1100    ' move x axis 1100mm
            M01

This is because it should be a panel sizing machines, and there is only one axis
but the cam software works at four levels, when the signal changes (x-y  x-u  x-v)
is waiting for an external signal.

Regards Csaba

10
VB and the development of wizards / Y, U, V Change X DRO
« on: June 22, 2010, 04:45:26 PM »
Hi!

how macro to be any axis in g code the x-axis move?
If G code Y300 you move X-axis 300
              U300 you move X-axis 300

thanks
Csaba

Pages: 1 2 »