Hello Guest it is September 21, 2023, 08:41:35 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - furkan

Pages: 1 2
1
General Mach Discussion / Re: Mach3 on another computer
« on: May 22, 2013, 09:58:50 PM »
angel tech,

Oh, understood. It was already off.

Tweakie.CNC,

I found the old Toshiba laptop that I used to use.  It worked like a charm for hours. But then suddenly it stopped working. On mach screen everyting seems ok, seems like working but nothing happened on the CNC side.

2
General Mach Discussion / Re: Mach3 on another computer
« on: May 22, 2013, 09:30:52 AM »
Chaoticone,

Thanks for the answer. But once I could use Mach 3 on a laptop. Maybe there's something about laptops hardwares.

angel tech,

I couldn't really catch. Do you mean xml file says the software that it is off?

3
General Mach Discussion / Mach3 on another computer
« on: May 22, 2013, 08:28:32 AM »
Hi,

Yesterday, my old computer was broken while I was using my CNC. Then I installed mach3 on another laptop with a parallel port. I moved the mach3mill.xml file to the new installed mach3 folder. But now I'm not able to use my CNC. The steppers doesn't move. They don't give any reaction.

I realised that when I load and start a G-code or drive the motors manually, the X Y Z location adresses on the screen doesn't change. Mach3 starts timing the elapsed time but it seems Mach3 doesn't work.

Addditionally, I moved the Mach3 folder from the old computers hard drive (without installation). Mach3 worked but still the same problem.

Now I don't now where to look at to solve the problem  :-\

P.S:
I checked the parallel port root adres,
Checked the motor pins&ports,
Checked the cables,

anythings seems ok.


4
General Mach Discussion / Re: Making a laser cutter
« on: May 12, 2010, 08:54:59 AM »
hmm. So did you isolate the spindle motor with that black box?

5
General Mach Discussion / Re: Making a laser cutter
« on: May 12, 2010, 07:42:32 AM »
Hi Tweakie,

Thanks for your answers and suggestions. And sorry that I  couldn't look at here for so long.

As I searched making PCBs with laser is something expensive, difficult and a bit dangerous in home conditions.

Your suggestion can work. But if I will again use acid, I prefer to use a PCB pen with cnc as I do now.

6
General Mach Discussion / Making a laser cutter
« on: April 05, 2010, 01:23:16 PM »
Hi there,

I have built a cnc with about 60*60 dimensions. I'm using a dremel hand tool instead of a spindle motor to work less noisy but it still works too noisy for an apartment. I thought that maybe I could use a laser so I could use my cnc anytime I want. But I don't know much about lasers. I'm generally cutting 5-8 mm plexyglass, or making pcbs. What kind of laser that I need to use? And is it possible to make pcb with laser? If yes, is it possible to make it with the same laser that I can cut plexy? And also what kind of troubles I might see while the prosses of changing my machine to a laser cutter?

thanks.

7
General Mach Discussion / Re: Speed and noise problem
« on: February 21, 2010, 02:09:26 PM »
thanks a lot.

8
General Mach Discussion / Re: Speed and noise problem
« on: February 21, 2010, 02:08:55 PM »
Ok. So I think no problem with hardware but the codes. I'll try to create a correct code and try again.

9
General Mach Discussion / Re: Speed and noise problem
« on: February 21, 2010, 01:12:14 PM »
It must be bigger than 6 centimetres but I'm not sure because I didn't save the dxf file.

10
General Mach Discussion / Re: Speed and noise problem
« on: February 21, 2010, 01:07:38 PM »
Oh I drow it in Ares (an electric circuit software) and used lazycam to convert dxf file to the gcode, it must be bigger.
Mach3 is set to metric. 

(by the way, I appreciate you, even I'm not enough to understand you try to help me with patience.)

Pages: 1 2