Hello Guest it is March 28, 2024, 12:55:59 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - carmine

Pages: 1
1
Mach3 under Vista / Re: Getting up and running in Vista
« on: February 01, 2010, 10:38:46 PM »
thank you Russ

2
Mach3 under Vista / Re: Getting up and running in Vista
« on: February 01, 2010, 10:21:37 PM »
Hello Russ do you have a minute
i rewiered the intire machine i also purchased a new break borad for a new application tried to connect the new break out bord to my computer and still nothing it is moving could be vista stopping from running
on the frist machine i took reading of a-,a+,b-,b+ and the last to have 12 v running but notihing was moving any idea?thank you again

3
Mach3 under Vista / Re: Getting up and running in Vista
« on: January 30, 2010, 09:13:21 PM »
thank you very much i hope my inexperience di not incovinienced you to much

4
Mach3 under Vista / Re: Getting up and running in Vista
« on: January 30, 2010, 09:03:18 PM »
no please no confution the digram that you send me seam to make more, sense like i said before the Keling guy keep saing that the computer sure let out 5v true the DB cable but i tried several tower all with 3.7v volt to there parallel port so i thank you for all your help
1 more question which is the ENABLE?thank you russ

5
Mach3 under Vista / Re: Getting up and running in Vista
« on: January 30, 2010, 08:09:05 PM »
and in regard your last question keling keep repeting that the out put from the DB25 sholud be 4.7v to 5v

6
Mach3 under Vista / Re: Getting up and running in Vista
« on: January 30, 2010, 07:54:25 PM »
Thank you very much Russ please allowd me to 2 more question
1 in the drawing that you send me at frist woul i be able to jump 5v power from terminal 5v to EN terminal or i need a different source of power?
2i have 4 different jumper on my board you are tell me that moving one of the jumper will power bust the 3.7 volt and make 5v or allow the brak board to work with lees v?in the second drawing is different wiring schematics will wor also for my application?
thank you very much for the magnificent help

7
Mach3 under Vista / Re: Getting up and running in Vista
« on: January 30, 2010, 07:19:59 PM »
yes itis similar to ma drawing i can't upload to show you but if you copy and past this link it is the one that i have(this is 4 axis i only have 3 axis) http://www.kelinginc.net/KL-4030WithDB25.pdf

8
Mach3 under Vista / Re: Getting up and running in Vista
« on: January 30, 2010, 07:08:29 PM »
Language to complicated for me once agai thank you for try to help it is very appriciate
now what do you mean with board may be opto isolated but NOT buffered
and also can you help me or tell me if there is a esear way to make the machine move?

9
Mach3 under Vista / Re: Getting up and running in Vista
« on: January 30, 2010, 06:53:53 PM »
Thank you for reply
Yes i do have a 5v pwer supply but is only operation is to put 5v to the micro stepping driver
the 5v that suppost make the stepper motor moving should come from the computer that what i been told by seller

10
Mach3 under Vista / Re: Getting up and running in Vista
« on: January 30, 2010, 06:37:50 PM »
dose any one ever got a problem running Mach 3 with vista problem such only 3.7 volt fromparallel port to break board unstead of 5 volt?
can something like this will stop mach 3 from running my table i use :6 axies Breakout board, Optically Isolated , E-Stop or Limit Switch can be wired, KL-DB25,
KL- 4030 Micro stepping Driver 40 VDC /3.0A
3 PC NEMA 23 BIPOLAR STEPPER MOTOR 270  oz-in , 1.8 degree, 4 Leads
please help it is almust a week that im tring trouble shooting the problem over the phone with the seller from Kelinging

Pages: 1