Hello Guest it is February 28, 2020, 07:19:38 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Kola

Pages: 1
1
General Mach Discussion / Re: Problems threading on the lathe
« on: March 25, 2010, 04:45:17 PM »
Hi Art

 License name Kola cnc
Version R3.043.000
 Spindle Feedback" option is checked.
I have to link intrnet turning the ID check?

  Kola

2
General Mach Discussion / Re: Problems threading on the lathe
« on: March 24, 2010, 05:30:54 PM »
Hi Art!

 test: spindle true 500rpm , the programmed G95 feedrate 1mm Spindle 250   -  true feedrate 0.5mm
        spindle true 500rpm , the programmed G95 feedrate 1mm Spindle 500   -  true feedrate  1mm 
        spindle true 500rpm , the programmed G95 feedrate 1mm Spindle 1000  -  true feedrate 2mm

  why is this problem?

   Kola

3
General Mach Discussion / Re: Problems threading on the lathe
« on: February 28, 2010, 02:39:12 PM »
Hi Art!

The situation has not changed even after the update!
The lathe spindle number of pulses is best?
Timing 8 to me that a lot of gap now?
Kernel 65 000 Hz, 2.7 GHz Intel Pentium processor.
I ask you to debounce interval 500 and 100 index debounce setting to good?

  Hi Kola

4
General Mach Discussion / Re: Problems threading on the lathe
« on: February 23, 2010, 01:19:18 PM »
Hi friends!
My problem is that the thread cutting 30mm round is longer than miss, but the following cuts of all good in the beginning but then miss the 30mm length of sync.
setting the timing gap 8 (a gap twice as large as the others), the PWM spindle - Hitachi L100 inverter, half ratio, 50 Hz - 700 rpm M30x1.5mm l = 130th
The 12 passes and only 30mm high early next Threading bad!
What is the problem? Mach3 2.61, WindowsXP SP2, Intel pentium4, 1Gb RAM
Sorry but the google translator I wrote!

 Kola

5
General Mach Discussion / Re: Front & rear toolpost in Turn 42.020
« on: January 24, 2010, 01:18:49 PM »
One application of the front and rear tool problem http://www.cnctar.hunbay.com/KoLa/Vide%F3/Egy%20k%E9s.avi

6
Üdvözletem!
Azt  szeretném kérdezni van-e itt valaki akinek sikerült a hátsó késtartó beállítása úgy hogy lehessen váltani menet közben az elsőre és vissza a g kódban programozva!

 üdv Kola

7
General Mach Discussion / Re: Front & rear toolpost in Turn 42.020
« on: January 08, 2010, 03:40:46 PM »
Hi, you can not setup the rear tool holder system!
Today I tried so that the rear tool holder, Front configured and saved to the table tool, programming should be a negative sign on the x-axis coordinates, and so works well

  Welcome Kola

8
General Mach Discussion / Re: Front & rear toolpost in Turn 42.020
« on: January 07, 2010, 06:12:18 PM »
I don't know how to setting the front  & rear toolpost .
If i set rear tool then the system is down!!!

10
General Mach Discussion / Re: Front & rear toolpost in Turn 42.020
« on: January 07, 2010, 05:13:50 PM »
Hi Im Kola from Hungary - Magyarul szeretnék kérdezni a mellső és ahátsó késtartó beállításiról ha van itt egy honfitárs?

Pages: 1