Hello Guest it is August 14, 2020, 07:39:32 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 55CHEVYGUY

Pages: 1
1
General Mach Discussion / Re: STILL NEED HELP GUYS AND GIRLS
« on: September 11, 2009, 04:02:17 PM »
How do I get any other xml's  that all found

2
General Mach Discussion / Re: STILL NEED HELP GUYS AND GIRLS
« on: September 11, 2009, 03:03:49 PM »
In CONFIGATOINS IN PORTS & PINS ,MOTOR OUTPUTS  X,Y,Z ARE ENABLED ASIGNED PINS,ALSO CHECKED ARE DIR LOW AC & STEP LOW

3
General Mach Discussion / Re: STILL NEED HELP GUYS AND GIRLS
« on: September 11, 2009, 02:36:52 PM »
see attachments let me if they load

4
General Mach Discussion / STILL NEED HELP GUYS AND GIRLS
« on: September 10, 2009, 05:21:57 PM »
 
  USING MACH3 TO RUN PLASMA TABLE I DID SOMETHING TO CAUSE THIS PROBLEM
FIRST, NOT ABLE TO TURN RED LIGHTS OFF OR ZERO X,Y,Z,AND A THAT AFTER RESET IS GREEN
SECOND,AFTER LOADING G-CODE,PRESS START AND GCODE RUNS TO M3 AND STOPS AND THE DWELL LIGHT COMES ON EVERYTHING STOPS
VERY GREEN ON MACH3 AND ALL CNC
I HAVE SHEETCAM TRIING LEARN IT ALSO
 THANKS YOU IF YOU HELP
      55CHEVYGUY

5
General Mach Discussion / Re: Help for newbie
« on: September 08, 2009, 07:46:02 PM »
I didn't find xlm backups found plasma xlm files but know how to use them and really don't think this file is what you're talking about. see attachment..I also reinstalled mach 3 since trouble,sure that will make a difference.
Also noticed yellow lite blinking on dwell and spindle speed that's gcode gets to m3 and stops

6
Lannie here
I'm new to cnc I build my plasma table a few months ago.very excited with the things already cut.
My interests are women and cars,I have a wonderful woman,that leaves cars boy do I like cars. That's why a got the plasma cutter.
I live in las vegas and last year at S.E.M.A. show seen my first plasma table working,and said gota have one.Having trouble with software (CHECK OTHER POSTS) If you can help thank you.
I 'm looking forward to being part this group.
Lannie
If ever in town let me your coming,you know what they say in Vegas (if you come you 'll have fun) if it happened in Vegas it stays in Vegas!!!

7
General Mach Discussion / Help for newbie
« on: August 31, 2009, 11:01:12 AM »

I'm very new to cnc. Have a plasma table I build from a camcutcnc kit with a Lincoln's 25 plasma cutter. At first I was able to cut several of the sample gcodes using mach3 that came with kit Then got sheetcam to try some dxf files that's when everything went to sh...... :somehow I've change configuration in mach3 first while loading gcode the screen went to a blank screen.when I finally got back to main screen the lights next to x,y,z,and a wouldn't turn green.Again I was able to get X,Y,Z to turn green but not A.Now when after loading gcode and starting cycle it stops at M3 if I hit start again the gcode resumes but not the plasma.
I think M3 must turn on or off plasma cutter.This is how new I am don't know g or m codes and other term of the industry (e i  DRO'S ,THC,AND WORK OFFSETS to say a few)
CAN ANYONE MAKE SENSE OF MY PROBLEM AND HELP
THANKS
Lannie

8

I'm very new to cnc. Have a plasma table I build from a camcutcnc kit with a Lincoln's 25 plasma cutter. At first I was able to cut several of the sample gcodes using mach3 that came with kit Then got sheetcam to try some dxf files that's when everything went to sh...... :somehow I've change configuration in mach3 first while loading gcode the screen went to a blank screen.when I finally got back to main screen the lights next to x,y,z,and a wouldn't turn green.Again I was able to get X,Y,Z to turn green but not A.Now when after loading gcode and starting cycle it stops at M3 if I hit start again the gcode resumes but not the plasma.
I think M3 must turn on or off plasma cutter.This is how new I am don't know g or m codes and other term of the industry (e i  DRO'S ,THC,AND WORK OFFSETS to say a few)
CAN ANYONE MAKE SENSE OF MY PROBLEM AND HELP
THANKS SO MUST
ROSS THE 55CHEVYGUY

Pages: 1