Hello Guest it is March 28, 2024, 07:15:54 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - artrans

Pages: 1 2 »
1
FAQs / stepper motor controler
« on: February 12, 2009, 08:24:13 AM »
does anyone no of a way to hook up a gecko to a steper with a mpg to run a stepper with out a pc if yes can you draw a wireing diagram
thanks art

2
General Mach Discussion / mach3 and laptop
« on: February 08, 2009, 08:17:49 PM »
i have been trying to run mach3 with a laptop it has been giving me a hard time but I think it may be ok now
But i have seen someway said that one should not run mach3 on a laptop if that true why and what problems should i see.

3
General Mach Discussion / spindle problems mach3
« on: February 07, 2009, 02:12:06 PM »
I have spindle problem and tryed some of the differant post answer but still have issues
1 hit spindle button nothing happen flashs yellow have to hit reset below spindle button to turn spindle on when I do that I get a massage by the red reset switchpwm bumped to minamal setting.
2 calibrate spindle nothing in that box seems to work the spindle
3 if I input rpm or pick spindle speed lets say 3000 rpm when I hit the spindle start button the speed disappears and says zero and the spindle does not turn on Iget the same problem stated in number 1
4 to make life easy is there a way to override the spindle and turn it on by hand.
IT is a maxnc15cl thanks for anyhelp it been a long hard road uphill

4
General Mach Discussion / mach3 problem
« on: February 07, 2009, 11:27:03 AM »
hello using mach 3 with a maxnc everything works except how do you run the spindle i click on spindle button and i get too slow for pulley.using min. that says that to the right of the clear button below the reset button if I type in the spindle speed and hit the spindle button speed goes to zero anybody have a idea as to whats wrong thanks art

5
FAQs / Re: MAXNC15
« on: February 05, 2009, 08:19:23 AM »
thanks chip for the info and your time

6
FAQs / milling a part
« on: February 04, 2009, 04:33:34 PM »
i want to mill a connecting rod out of 1/4 plate alum to start so lets say I have a piece of plate 4 inches wide 10 inches long a mount that in the mill do I need a hole in the center of the connecting rod to hold it to the machine or what happens when it is cut out. ???

7
FAQs / Re: MAXNC15
« on: February 04, 2009, 03:35:19 PM »
He is some gcode i got for a connecting rod I am try to make can some please teach me something here 1st LINE IS THAT THE SIZE OF THE RAW MATRIAL NEXT F WHERE DOES THE F COME IN OTHER WHAT I THINK IT MEANS AND IAM F%^$$#KED but really waht do they mean
what i no xyz table got that, m/ motor on off,s/speed now m5m30 whats that and with the g code posted I still have to set the depth or z
do I have anyof this right or should I throw in the towel. This make one fell stupid I can rebuild automatic transmission computer controled all day this is make my hair hurt but I will not give up although i have come close. thanks for any help



G90G80G49
G0 Z1.0000
G90.1
S1000
G0 Z1.0000
G0 X3.0000 Y1.5000
M3
F1.000G1 Z0.0000
F1.000G1 X3.0000 Y3.0000
G1 X5.0000 Y3.0000
G1 X5.0000 Y1.5000
G1 X3.0000 Y1.5000
G0 Z1.0000
G0 X3.3269 Y2.2500
F1.000 G1 Z0.0000
G2 X3.3269 Y2.2500 I4.0000 j2.2500
G0 Z1.0000
G0 X3.5000 Y3.2500
F1.000G1 Z0.0000
F1.000G1 X4.5000 Y3.2500
G1 X4.1250 Y8.7500
G1 X3.8750 Y8.7500
G1 X3.5000 Y3.2500
G0 Z1.0000
G0 X3.2387 Y3.0000
F1.000G1 Z0.0000
F1.000G1 X3.6911 Y9.0000
G0 Z1.0000
G0 X3.8288 Y9.0000
F1.000G1 Z0.0000
F1.000G1 X3.8681 Y9.0000
G0 Z1.0000
G0 X3.5000 Y9.0000
F1.000G1 Z0.0000
F1.000G1 X4.5000 Y9.0000
G1 X4.5000 Y10.0000
G1 X3.5000 Y10.0000
G1 X3.5000 Y9.0000
G0 Z1.0000
G0 X3.7205 Y9.5000
F1.000 G1 Z0.0000
G2 X3.7205 Y9.5000 I4.0000 j9.5000
G0 Z1.0000
G0 X4.7139 Y3.0000
F1.000G1 Z0.0000
F1.000G1 X4.3008 Y9.0000
M5
G0 Z1.0000
G0 X0 Y0
M5M30

8
FAQs / MAXNC15
« on: February 04, 2009, 03:06:01 PM »
OK NEW PROBLEM BUT i AM GETTING CLOSER THANKS TO SOME OF YOU  i HAVE A MAXNC15 WITH THERE SO CALLED NEW SOFTWARE WHICH LOOKS LIKE MACH3 i DRAW A PART IN CADSTD PRO SEND IT TO LAZYCAM LOAD TO MACH3 i GET GCODE THAT'S A BIG STEP BUT NOW i TRY TO GET IT INTO MAXNC VERISON OF MACH3 AND i CANNOT ANY BODY HAVE A ANSWER FOR THAT THANK YOU ART
ANYBODY FROM NEW YORK THAT CAN DO A HANDS ON THAT WOULD BE A DREAM COME TRUE FOR ME NIGHTMARE FOR YOU

9
FAQs / Re: dfx to gcode
« on: February 03, 2009, 01:18:42 PM »
OK thanks I found it like you said but a few more stupid questions really new at this so bare with me. I still need to edit for motor on and speed
and motor off I have a maxnc15 other then spindle speed and on off I would then zero on the alum plate and run do I have that right. thanks for any advice I need it.

10
FAQs / Re: dfx to gcode
« on: February 03, 2009, 12:24:37 PM »
I loaded to lazy cam also and I see the chains how do I see the code in lazy cam it says saved as tap.file but where is that file and how do you read the gcode and then when I do that i export again to the machine softwear. sorry I not details. thanks art

Pages: 1 2 »