Hello Guest it is October 28, 2021, 12:16:38 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - TDAY

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 »
1
Mach4 Videos / Re: Mach4 Quicky #6 - Disable Keyboard Plugin
« on: September 13, 2016, 07:36:01 PM »
Awesome. :) Thanks again for your work.
Troy

2
Mach4 General Discussion / Re: Dry Run Mode
« on: September 10, 2016, 07:03:03 PM »
It would be much nicer and more industry standard if you can do a dry run before actual machine motion. There is nothing like Mach3s OEM code 178(OfflineToggle), for Mach4?
Troy

3
Mach4 General Discussion / Re: Dry Run Mode
« on: September 09, 2016, 05:36:55 PM »
My setup is AC servos, so i cant do that. Mach3 had the option of disabling all outputs so you could simulate a run. Seems like there would be something like this in Mach4?

4
Mach4 General Discussion / Dry Run Mode
« on: September 09, 2016, 01:02:59 PM »
Hello all,
 How can Mach4 be put into a "Dry Run" mode? So one could run Gcode and preview it on toolpath, without any physical machine movement. Is there any Lua code that could be put into a button to change motion device to the Simulation Device?
Thanks,
Troy

5
Mach4 General Discussion / Re: Mach4 Keyboard Emulation
« on: September 07, 2016, 12:29:54 PM »
Is there a way to have the keyboard plugin automatically disabled when the focus is not in the Mach4 window, and re-enabled when the focus goes back to Mach4 window?
+1 for this

Same here.

Or at least when you open the Gcode editor. Anyone know if this is possible?

6
Mach4 Plugins / Re: Shuttle Pro question
« on: September 07, 2016, 07:43:46 AM »
I enabled MPG0 and and set axis selection buttons in the plugin and all works now. :) Big plus being able to adjust the accel and velocity, much nicer movement now. :)

Thanks again,
Troy

7
Mach4 Plugins / Re: Shuttle Pro question
« on: September 06, 2016, 07:36:12 PM »
I will give it it a go tomorrow when i get back to the mill.
Thanks again,
Troy

8
Mach4 General Discussion / Re: Mach4 Keyboard Emulation
« on: September 06, 2016, 07:08:52 PM »
Awesome tutorial. One step i was missing was the restart of Mach4.
I got your example working for feed hold, but where do i find the command for CycleStart? Is there a list of these somewhere like Mach3s list of OEM codes?

Thanks,
Troy

9
Mach4 General Discussion / Re: Mach4 Keyboard Emulation
« on: September 06, 2016, 02:31:45 PM »
So how do you add another function to the Key Board Plugin. All i see is Jogging functions. Would like to add a keyboard key for CycleStart and Cycle Stop.
Troy

10
Mach4 Plugins / Re: Shuttle Pro question
« on: September 06, 2016, 02:03:42 PM »
Iam now using Mach4 development version: 4.2.0.3155. And still get no movement from inner jog wheel.
Troy

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 »