Hello Guest it is October 02, 2023, 08:34:17 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - vertigo

Pages: 1 2 »
General Mach Discussion / Re: MACHsupport Please
« on: July 29, 2012, 04:38:54 AM »
yeah that worked..I put the file in the wrong location and MACH3 couldn't find it..Thanks Hood

General Mach Discussion / Re: MACHsupport Please
« on: July 28, 2012, 08:18:29 PM »
I found the DAT file hood..now what do I do? MACH3 still says "Demo Version"

General Mach Discussion / Re: MACHsupport Please
« on: July 28, 2012, 12:23:32 AM »
MACH3 licence

General Mach Discussion / Re: MACHsupport Please
« on: July 27, 2012, 06:12:19 PM »
thanks Hood..will do, I don't get it I just setup a new operating system and both have no Licence keys. I can't see a conflict but there must be one that I have overlooked. NB: one is XP and the other Windows7. it shouldn't have asked me for licence on system OS already running. Very confused, but many thanks Hood.

General Mach Discussion / MACHsupport Please
« on: July 27, 2012, 12:43:57 PM »
Guys, I just started a new home grown CNC operation running XP system and running (min) ram and lost all my keys..
I can't work it out. My first system worked fine untill I booted up the other PC and now both PC's are (DEMO) mode..WTF.
My other PC worked fine until now. I would like someone from supportMach to reply please. I as far as I know have done nothing wrong apart from forget bits and bytes and so on. Funny I was about to run the EXE to test drivers and (demo) showed up...Help Please

General Mach Discussion / Re: Australian suppliers (CNC)
« on: July 19, 2012, 11:27:34 AM »
Hi guys, thank you very much of your input to the convo, as for now I will be using steve's link. I thank you all. I do however have four cnc mills already but they are out in the country I am currently living in. The cost of bring them here out weighted the cost to build the machine I need atm...again thank you all.

General Mach Discussion / Re: Australian suppliers (CNC)
« on: July 17, 2012, 08:33:02 AM »
thanks Steve.

General Mach Discussion / Australian suppliers (CNC)
« on: July 14, 2012, 09:57:26 PM »
Hi guys,
I am looking for an afordable supplier for cnc parts (everything) I would prefer the company to only sell cnc parts so I can get the best prices available.  I must be able to pay by Paypal. Anyone that can help me out please. Post links as well if possiable. I would also prefer NSW suppiers so I can look at the parts before I buy them (incase of mistakes or suitabilities)

General Mach Discussion / Tool head direction
« on: July 09, 2012, 06:51:40 AM »
I haven't had a need to do this, but is there any reason for a spindle to run in reverse..apart from threading a hole.  I ask because I have a controller that will allow me to reverse the spindle..any advice would be great.  Anyone that can give me advice on weather or not to disable this function....I can program it to not allow reserve spindle speed, but looking for advice before I do it. Its very hard to change the disable function after I impliment it.

General Mach Discussion / Re: Jog not working.
« on: July 05, 2012, 10:40:38 PM »

Thank you.  I have been away from MACH3 for to long and I am still re learning the program again.

Pages: 1 2 »