Hello Guest it is December 01, 2021, 08:16:45 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - celticbern

Pages: 1
1
General Mach Discussion / Re: Can I turn Off Cutter COmp on Mach 3 Side?
« on: January 25, 2007, 07:12:01 AM »
I have the G41 (comp left) in the G-Code....

it still runs off

2
General Mach Discussion / Can I turn Off Cutter COmp on Mach 3 Side?
« on: January 25, 2007, 06:04:17 AM »
Hello,

I am having problems with the Cutter Comp on my Celtic Wine Racks....

I set it to "Comp Left" on the BobCad v20 program side and create the G-code. At some point when I am running it on my CNC machine the cutter comp seems to lose where it is going.

I know the basics only....Can I turn off the cutter comp somewhere in the "Config menu" on Mach 3 ???

thanks
bernie
http://www.carvingceltic.com

3
Brian,
i recieved a phone  call.....calling him back now......I hoping tofind someone local to tutor me

4
Hello,

I live in Des Plaines Illinois and need someone to help me with my software & control box....

I make Irish and Celtic Wood Carvings and use my 30x30 machine to rough out my work.

My old computer fried and I am lost with getting everything back into working condition. I have installed mach 3 but need help getting the computer to talk to the control box.

If you live in the chicagoland area and woould like to help I would be more than happy to pay you for your time.

Best Regards,
Bernie Fay
847-800-1234
http://www.carvingceltic.com
http://www.celticity.com

5
General Mach Discussion / Re: Beginner needs help W/ Mach 2 Mill
« on: October 30, 2006, 11:40:53 PM »
What are the advantages of Mach 3 instead of Mach 2?

6
General Mach Discussion / Re: Beginner needs help W/ Mach 2 Mill
« on: October 30, 2006, 10:53:08 PM »
Thanks..

I will download the manual and start reading and whenI get stuck I will post.....

It's time I learned this.

7
General Mach Discussion / Re: Beginner needs help W/ Mach 2 Mill
« on: October 30, 2006, 10:13:15 AM »
How do I tell what the hardware is?

8
General Mach Discussion / Beginner needs help W/ Mach 2 Mill
« on: October 30, 2006, 08:57:14 AM »
Hello All,

I just downloaded Mach 2 on my new computer. I had it on my old computer which fried & I did not write down any of the ports and pins etc...

I use Mach 2 to rough out my Celtic wood carvings.

Can Someone please help with ports & pins, input signals, Outpus signals, output pins......I turn the porter cable router on manually, vacuum manually.

I recall from two years ago that there was not too much I had to program on the Mach side and I have all of the motor tuning already set.

Basically I just need the printer port stuff to send from the computer to the control box and any suggestions (aside from "write this down dummy")

Kindest Regards,

Bernie Fay

9
General Mach Discussion / Screen Works But won't run My CNC Maching
« on: August 06, 2006, 12:30:02 PM »
Hello All..

For some reason I screwed up my computer to control box.....The Mach 2 screen shows the x,y,z moving when I press the HOTKEYS but it will not move the CNC motors....I must have locked out something or pressed the wrong key.

I double checked all cables etc and still nothing.

I have been using Mach 2 for a long time for my Irish and Celtic Wood Carving Rough Outs and it is wonderful.

I cannot figure out what I locked out but any input will be greatly appreciated.

Kindest Regards,

Bernie Fay
http://Http://www.carvingceltic.com


Pages: 1