Messages

1

Mach4 General Discussion / Re: M4 update to 5000 version, result: system failures

« on: January 21, 2023, 04:30:15 AM »

hi Steve,
thank you for You're reply. as far as i can see the problem is in the cslabs plugin. i contacted CS-lab support about this. if there is a solution or an update i wil post that here.

regards, TanTanCNC

2

Mach4 General Discussion / Re: M4 update to 5000 version, result: system failures

« on: January 16, 2023, 02:53:08 PM »

Right, thanks!

3

Mach4 General Discussion / Re: M4 update to 5000 version, result: system failures

« on: January 16, 2023, 12:07:50 PM »

hi Graig,
does the screenset contain all the configuration information like Input/Outputs, motortuning and so?
i would think this info is stored in the .ini file
regards, TanTan

4

Mach4 General Discussion / Re: M4 update to 5000 version, result: system failures

« on: January 15, 2023, 02:30:21 PM »

thanks for all the replies. i removed the software (mach4 and CSLabs), i cleaned the registry and reinstalled the 46xx version. i am up and running again with this version. for installing a new version i will take you're advice to rename my current directory..
i will post results from the testing which seems strange to me or which do not work as in the 46xx version.
thanks all!

5

Mach4 General Discussion / Re: M4 update to 5000 version, result: system failures

« on: January 09, 2023, 11:31:50 AM »

hi, thank you for you're reply,
i wish i had done that.... i switched back to Mach3 and all works fine. not sure if i want to go to Mach4 again.... 

6

CS-Lab / update to M4 .5000 version

« on: January 07, 2023, 03:22:04 AM »

i have an EMCO mill converted to mach3 and that runs for a few years now. i use CSLABS CSMIO/IP-S six axis and pokeys for the pendant. the pc is an intel nuc with W10/8GB internal RAM. i converted it to M4 (previous version 46..) all went wel, i made the software for the toolchanger, perfect. (https://youtu.be/a72-Q8TJUow) i did an upgrade to the .5000 version. now CSLABS comes with PID fault: error 1092
i reinstalled M4, made a new clean profile and entered all the setting.. nothing works.
i hope to get some ideas...

7

Mach4 General Discussion / M4 update to 5000 version, result: system failures

« on: January 07, 2023, 03:15:11 AM »

i have an EMCO mill converted to mach3 and that runs for a few years now. i use CSLABS CSMIO/IP-S six axis and pokeys for the pendant. the pc is an intel nuc with W10/8GB internal RAM. i converted it to M4 (previous version 46..) all went wel, i made the software for the toolchanger, perfect. (https://youtu.be/a72-Q8TJUow) i did an upgrade to the .5000 version. now CSLABS comes with PID fault: error 1092
i reinstalled M4, made a new clean profile and entered all the setting.. nothing works.
i hope to get some ideas...

8

VB and the development of wizards / Re: Edge detection on input

« on: January 17, 2016, 10:40:00 AM »

see code i posted in my first post. that did not see input1 changing.
i call a sub in the while loop that reads the input. that works.

tnx

9

VB and the development of wizards / Re: Edge detection on input

« on: January 16, 2016, 03:01:29 PM »

hi,
it works,
mach does not read inputs within a while loop.

https://youtu.be/39QgfGTrPZo

tnx for your replies

10

VB and the development of wizards / Re: Edge detection on input

« on: January 14, 2016, 11:33:37 AM »

hi

yes the input changes in the diagnostic screen. i hope the frequency of the inputsignal is not to high for this basic code. i will test it tomorrow with a manual switch,

as far as i can see the code should detect an edge...

tnx for your replies.