Hello Guest it is October 22, 2020, 08:08:57 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bjcnc

Pages: 1
1
General Mach Discussion / Re: Spindle wont start, keyboard jog doesnt work
« on: November 26, 2009, 07:56:19 AM »
I have found that I can only jog with keyboard when there is NO G CODE LOADED Must use the tab  out function if G code is loaded. Is this correct

2
General Mach Discussion / Re: z-axis plunging
« on: November 19, 2009, 07:02:27 PM »
Thank you for your help. I am glad to know that mach is working fine . Thank you again

3
General Mach Discussion / Re: z-axis plunging
« on: November 19, 2009, 06:35:48 PM »
It is from bmp2cnc

4
General Mach Discussion / Re: z-axis plunging
« on: November 19, 2009, 05:43:00 PM »
it does a rapid move to .1 then goes down .2  carves up and down as in the g code to different heights . I think  then the real question might be how do you set it up so that one could carve from the top down rather than plunging down to the lowest point  and carving up  to the top. 

5
General Mach Discussion / Re: z-axis plunging
« on: November 19, 2009, 04:53:28 PM »
we place the z on the or right above the piece of wood and zeroing it. then when we start to run the gcode  it just dives right down to -0.2

6
General Mach Discussion / Re: z-axis plunging
« on: November 19, 2009, 04:11:35 PM »
is this the xml you were asking for if not sry can you explain exactly what it is

7
General Mach Discussion / Re: z-axis plunging
« on: November 19, 2009, 04:04:16 PM »
here is the code atleast it should be let me try to find the xml

8
General Mach Discussion / Re: z-axis plunging
« on: November 19, 2009, 03:52:28 PM »
they are all empty and at 0... the machine has sat idle for over a year now and before it sat it was working great just all the sudden started doing this

9
General Mach Discussion / Re: z-axis plunging
« on: November 19, 2009, 03:30:00 PM »
here is the begining dunno how to send it all because it is too many "words"
O0001(AEMBOS1A.NC)
N1 G00 G17 G20 G40 G49 G80 G90
N2 T1 M6 (CONIC-R  1/8 - DEG 15 - R 0.025 )
N3 G00  X0.  Y0. M03
N4 G43H1  Z0.1 M8
N5 G01 Z-0.2 F40
N6 X0.7677
N7 X0.7879 Z-0.1661
N8 X0.798 Z-0.1536
N9 X0.8081 Z-0.152
N10 X0.8182 Z-0.1536
N11 X0.8283 Z-0.152
N12 X0.8384 Z-0.1598
N13 X0.8586 Z-0.1975
N14 X0.8687 Z-0.2
N15 X1.3737
N16 X1.3838 Z-0.199
N17 X1.3939 Z-0.1873
N18 X1.404 Z-0.1818
N19 X1.4141 Z-0.1873
N20 X1.4242 Z-0.1818
N21 X1.4343 Z-0.1943
N22 X1.4444 Z-0.2
N23 X2.

10
General Mach Discussion / z-axis plunging
« on: November 19, 2009, 02:34:32 PM »
when my z axis is plunging into the matterial it goes to the max z depth for the entire piece and either locks up the whole machine or drags my piece of wood with it  does anyone have any ideas as to what it could be

Pages: 1