Messages

11

General Mach Discussion / Re: need a macropump

« on: June 10, 2010, 12:38:35 PM »

Thanks

Yes I agree! That is why I only wanted it to jog once .020.
Well my machine only uses one axis and if conditions are right I will lose -.001 every few cycles. I have went through solenoid valves put capacitors on them, shielded my wires all with no avail. I do have a poxy sensor that will disable the start button if it travels to far down, should this occur the operator will jog the system up and continue running parts (I have a macro that will zero the x axis each time the g code starts). I would like to get rid of the machine operator doing this and have the mach do it.
what do ya think?
josh

12

General Mach Discussion / need a macropump

« on: June 10, 2010, 10:09:11 AM »

Greetings

I would like to have a maropump that would jog my x axis +.020 if an input is not closed. I need it to do it only once(meaning not a continuous jog until it finds the input) and only when the system is in its stopped condition. Can this be done?
thanks
Josh

13

General Mach Discussion / Re: macro for the non macro'ish

« on: March 09, 2010, 03:03:06 PM »

Thank you

14

General Mach Discussion / Re: macro for the non macro'ish

« on: March 09, 2010, 02:29:18 PM »

Second Try

15

General Mach Discussion / Re: macro for the non macro'ish

« on: March 09, 2010, 02:28:12 PM »

First Try

16

General Mach Discussion / Re: macro for the non macro'ish

« on: March 09, 2010, 01:58:02 PM »

Sorry about the confusion, its my constant state?
M3
M3
X  00.000 Y00.00000 Z00.00000 F550.00
M11 P2  < This is the command to turn output 4 on, or my heat.
G1 X -00.070 Y00.00000 Z00.00000 F010.0
M11 P7
G1 X -04.800 Y00.00000 Z00.00000 F080.0
M10 P2 < this is the command to turn it off,output 4, or my heat.
M10 P2
X -06.00 Y00.00000 Z00.00000 F130.00
G4 P1.7
X -06.300 Y00.00000 Z00.00000 F7800.00
M10 P7
X -06.400 Y00.00000 Z00.00000 F700.00
M11 P3
M11 P5
M10 P7
X -06.420 Y00.00000 Z00.00000 F800.00
G4 P0.1
M10 P5
M10 P9
M10 P7
X -06.450 Y00.00000 Z00.00000 F800.00
M6

17

General Mach Discussion / Re: macro for the non macro'ish

« on: March 09, 2010, 01:41:12 PM »

with P2 command

18

General Mach Discussion / Re: macro for the non macro'ish

« on: March 09, 2010, 12:41:36 PM »

Try this!

19

General Mach Discussion / Re: macro for the non macro'ish

« on: March 08, 2010, 06:26:32 PM »

I'm doing some diggin at home and found on one of my backup disks there is a file called machmill xml !! AAh ha! I'll pull that one out of my machine tomarrow and post it.

JOSH

20

General Mach Discussion / Re: macro for the non macro'ish

« on: March 08, 2010, 04:01:05 PM »

Humm. Not sure what to do next. ?