Machsupport Forum

Mach Discussion => General Mach Discussion => Topic started by: simolke on June 18, 2006, 03:13:20 PM

Title: Licening problem
Post by: simolke on June 18, 2006, 03:13:20 PM

I have a tag mill it workers fine with Mach 2 the motors wont work with Mach 3/4 an I bought license . I received secend copy of license an will still not work . Wizard said unlicensed file. can some one help :'(

Title: Re: Licening problem
Post by: Brian Barker on June 18, 2006, 05:11:47 PM

Look in mach3 Directory, is there a Mach1Lic.dat file? If there is not copy it from the Mach2 directory and place a copy of it in the Mach3 directory.

Title: Re: Licening problem
Post by: simolke on June 18, 2006, 05:31:58 PM

There a Machlic in the file  I have rerun file several times

Title: Re: Licening problem
Post by: Brian Barker on June 18, 2006, 06:30:55 PM

under help / about do you see your name?
Also you should be able to move your motors is you don't have a licanse... Could you please post your Mach2 and Mach3 XML files? I would like to check them to see if you have a bad setting.
Thanks
Brian

Title: Re: Licening problem
Post by: simolke on June 18, 2006, 07:01:37 PM

how do i post the file to you

Title: Re: Licening problem
Post by: simolke on June 18, 2006, 07:02:48 PM

how do i post the files to you so you can inspect to see if it's corrupted

Title: Re: Licening problem
Post by: simolke on June 18, 2006, 07:06:01 PM

Try this

Title: Re: Licening problem
Post by: simolke on June 18, 2006, 07:14:31 PM

hear is Mach2

Title: Re: Licening problem
Post by: Brian Barker on June 18, 2006, 08:03:24 PM

The Mach2 one is an XML not a sys file :) i think you got the wrong one..

Title: Re: Licening problem
Post by: simolke on June 18, 2006, 11:51:15 PM

Is whathyou want

Title: Re: Licening problem
Post by: Brian Barker on June 19, 2006, 09:08:57 AM

You need to set up your ports and pins :( If you look you have all the Step and Direction pins set to 2 & 3... once you set them to what you have in Mach2 you should be up and running :)

Title: Re: Licening problem
Post by: simolke on June 19, 2006, 06:18:15 PM

will this fix the wizard problem to . wizard said that I was unlicensed .

Title: Re: Licening problem
Post by: simolke on June 19, 2006, 09:53:11 PM

Motors running now . Last time I rubout Mach3 must have loss setup . Only problem now is Wizard stated unlicensed .

Title: Re: Licening problem
Post by: ART on June 19, 2006, 10:04:43 PM

Hi:

 Thats because the Conversational Wizardsa are a separate license available only from www.newfangledsolutions.com

Art

Title: Re: Licening problem
Post by: simolke on June 20, 2006, 10:50:59 PM

I wouldlike to thank youfor helping me through my  problems  an I will be gitting the wizard but don't like using paypal . Is there a nother way. ;D

Title: Re: Licening problem
Post by: Brian Barker on June 20, 2006, 10:56:09 PM

If you would like I can send you my address off line and  you could send a check..
Hope that works for you
Brian