Machsupport Forum

General CNC Chat => Building or Buying a Wood routing table.. Beginnners guide.. => Topic started by: Shelly on October 11, 2016, 02:18:37 AM

Title: Wiring of yoocnc 450 Kjb parallel port card to newforever inverter for Mach3 co
Post by: Shelly on October 11, 2016, 02:18:37 AM
Hi, hopping someone has done this. I have a yoocnc parrellel port card on 6040 machine and want to wire this in to run  newforever inverter
Using Mach3. There are 3 pins on the board, but don' t know whether these are opts isolated ? The can be configured to apply 0-10v signal to the inverter. any advise appreciated.  :)
Title: Re: Wiring of yoocnc 450 Kjb parallel port card to newforever inverter for Mach3 co
Post by: reuelt on July 06, 2017, 03:49:56 AM
The  450 Kjb parallel port card has only a PWM pin 17.
The Nowforever need Analogue 0-10V.
So your need a converter like
http://www.dx.com/p/maitech-pwm-turn-0-10v-digital-to-analog-module-green-318473?tc=AUD&gclid=EAIaIQobChMIidH98ZL01AIVkQQqCh0AsA4xEAQYAyABEgLK4fD_BwE#.WV3o2cAy_cs

Once you have Analogue 0-10V, you connect Analogue ground and  0-10V to aGND and AN1 respectively.  lower connection 1 and 3 from left on the Inverter.

You also need a pin that enables the PWM pin (probably Pin 1?) + digital ground. Top row  connection 1 and 5
Only 4 wires.

At inverter console change
P0000 set to 1
P0002 set to 2

PWM pin 17 must be  set to active low in Mach 3 otherwise you will have 10V (full speed) all the time.


PS: it might be cheaper to just change your BOB to a 5 axis BOB that includes Analogue 0-10V plus relay. Cost about $10

Title: Re: Wiring of yoocnc 450 Kjb parallel port card to newforever inverter for Mach3 co
Post by: reuelt on July 06, 2017, 04:07:23 AM
manual of a cheap 5 axis BOB with opto-isolation + 0-10V and a relay
www.hobbytronics.co.za/Content/external/473/5-axis%20manual.pdf

Nowforever VFD Manual: http://docdro.id/NYibeDM
Title: Re: Wiring of yoocnc 450 Kjb parallel port card to newforever inverter for Mach3 co
Post by: Tweakie.CNC on July 06, 2017, 04:32:10 AM
Here is another link for the E100 VFD manual:

http://ri.search.yahoo.com/_ylt=A0LEVxHE9F1Zd0UAiQlXNyoA;_ylu=X3oDMTByZnU4cmNpBGNvbG8DYmYxBHBvcwM5BHZ0aWQDBHNlYwNzcg--/RV=2/RE=1499358532/RO=10/RU=http%3a%2f%2fblog.opilab.ch%2fcnc%2fNOWFOREVER%2520MANUAL%2520E-100.pdf/RK=0/RS=MhJEQwYF4wnkaxEL9_cCyiMyl3Y-

Tweakie.