Machsupport Forum

Mach Discussion => General Mach Discussion => Topic started by: komar1970 on September 11, 2011, 09:05:35 PM

Title: mach3 ssetup
Post by: komar1970 on September 11, 2011, 09:05:35 PM

hi  I have   question my machine has backlash on Y axis 0.012mm on X axis 0.014mm  I cut a hole under Bearing 30mm everything is ok 29.95mm to 29.97mm dimensions

the part has to have dimension outside of 40mm x 40mm  but has 40.38mm on Y axis  and  on X axis 40.60mm  what's the problem?

I tried to set the machinery in different ways on 1/2 sherline , I tried to set the setup steps per unit but more worse comes out

Title: Re: mach3 ssetup
Post by: Hood on September 12, 2011, 07:16:38 AM

Do you have backlash enabled? If s disable and try again and see if that makes a difference, it could be its set wrong.
Hood

Title: Re: mach3 ssetup
Post by: komar1970 on September 12, 2011, 09:19:33 AM

I do not have enabled backlash. I try to switch on and see what will be I'll give you a message

Title: Re: mach3 ssetup
Post by: komar1970 on September 12, 2011, 09:21:14 AM

i  have gecko driver g540  motors is 200


200 x driver 10 macro steps is 2000 % pinch 5mm  give me 400 steps

Title: Re: mach3 ssetup
Post by: komar1970 on September 12, 2011, 09:52:12 AM

cut out with enabled backlash and it is the same  on X AXIS  is  40.65mm on Y axis  40.51mm

Title: Re: mach3 ssetup
Post by: komar1970 on September 12, 2011, 10:05:24 AM

setup

Title: Re: mach3 ssetup
Post by: komar1970 on September 12, 2011, 10:09:44 AM

setup

Title: Re: mach3 ssetup
Post by: komar1970 on September 12, 2011, 12:07:22 PM

ok if i go 400 steps  on the distance 3'' or 76.2mm  machine can not overcome this distance, missing distance is 0.18 mm  I have to change the step to 401 then it is slightly more than 76.2mm . but if I  increases  the distance to 152.4 is 6'' is again a problem, step 401 is not enough I have to give 402 step and again the machine goes a little more

Title: Re: mach3 ssetup
Post by: Hood on September 12, 2011, 02:13:24 PM

Try setting a value of 5 or more for the pulse and dir on Motor tuning page. You may even need to use Sherline mode if that doesnt help.
Hood

Title: Re: mach3 ssetup
Post by: komar1970 on September 17, 2011, 12:15:27 PM

the problem was in the Velocity and Accel. I fixed it but it is still a small problem

Title: Re: mach3 ssetup
Post by: komar1970 on September 17, 2011, 12:20:38 PM

the parts  is  40mm x 40mm  inside hole 30mm
 after i fix the   big problem   onli is problem  with one X axis
.
 parts cut out dimensions 40mm Y axis  hole 30mm  and X axis 40.20mm only the  X  AXIS  is problem

Title: Re: mach3 ssetup
Post by: komar1970 on September 17, 2011, 12:26:02 PM

Who will help me set this MACH3

Title: Re: mach3 ssetup
Post by: Hood on September 17, 2011, 02:44:08 PM

Are your steps per unit correct?
Hood

Title: Re: mach3 ssetup
Post by: komar1970 on September 17, 2011, 07:19:21 PM

i have  ste  to 400  and I lined up in a mach 3, but it's improved

Title: Re: mach3 ssetup
Post by: komar1970 on September 17, 2011, 07:31:06 PM

i fix the  problem  thanks  hood  for  help  is work  perect  if i  cut 70mm x 40  hole  20mm  is ok perfect size  if i cut 40 x 30  hole 1  perfect   if i cut 340mm  x 140 hole  50mm  smole proble  it is 340.01  that is ok

Title: Re: mach3 ssetup
Post by: Hood on September 18, 2011, 03:56:00 AM

Glad to hear it :)
Hood