Machsupport Forum
G-Code, CAD, and CAM => LazyCam (Beta) => Topic started by: Brian Barker on August 12, 2006, 10:58:38 PM
-
There is a new Lcam with the ability to read a Post file... The Post file can be changed in notepad and I have included an example .pst file for you to play with. There is also a Doc in the Zip file that should help you with the PostVars that you will need to make your post. Please test it and tell me if you think you would like to have other PostVars added and how it works for you. So you can get this on the FTP server under LazyCam/LazyCam 2.60 With Post Doc's.zip
Thank you :) and sorry I can't tell you more... I and burnt out and need to get some rest ::)
Thanks
Brian
-
Sorry Brian.
downloaded it and opened a file.
Selected a contour and it came up correct.
Went thru altering depth feeds etc but as soon as I alter the fisrt item LC freezes and locks up.
John S.
-
Hi, Brian
It locked up when I entered Start Depth and Final Depth in Layer Control column's only.
Been working on Plasma with no Z hight
M3/M5 generates first Dot/Pearce then leaves the remaining 4 with on Dot/Pearce plas/post options 0,0,1,1,20,1 not default..
Manual file mode seem's to work in any sub. Dir. now and post's code to the proper Dir. as assigned in LC.
But it will not update Mach3 even if there all in the same sub. Dir. even when its \Mach3.
Auto file create still post's code in \Mach3 as Gcodefilename.tap, not in \Mach3\Gcode where it should be, but will update Mach3 with new file.
Also it will not increment further file's with the same name, test1.tap, test2.tap as it did some time back, any way I think it did.
Working on some of the post's for LC option's, I have a way to go hear, could you post an example the way it could / would be.
Just some info so you wont get board.
Thank's Chip
-
John and Chip,
I have done some testing and I can't get it to happen to me :( Could you please tell me every step? I would love to get this fixed
Thankyou
Brian
-
Hi, Brian
This morning it was working fine, so I deleted the LC. XML should have re-named it o-well dumb dum me, it's back to freezing up the screen.
On in ital load of LC it doesn't generate an XML that's probably normal at this time it's freezing as before, even with a xml, I have close it and restart it have try-ed to get it to work and dup. the change that made it work.
Hears my non working xml maybe this will help, send me your working xml to try hear.
Loaded the Dxf I posted in LC, I can set / change all the item's in Layer Control Except Final Depth and Start Depth if thy are changed and OK is clicked the screen freezes and the only way to get out is Windows Task Manager End Task.
Thank's Chip
-
Hi, Brian
I have found that if I load a dxf file and set the Per Pass value to .5 that I can set Final Depth and Start Depth without lockup.
At this point I can change the Per Pass back to Default Value of 1 and seem to have no lockup problem.
This is without closing LC and restarting, once shutdown and restarted it will freeze again with out changing the value in Per Pass.
If I change Per Pass to .5 close the window then change it back to 1 default value again then the problem is gone till restart of LC again.
BTW the processer is at 100% when locked up, window's running, End Task will shut LC down .
Thank's Chip
-
Brian,
Here's the sequence.
Load LC.
Open x3beam.dxf
Accept defaults on load options
Click outer shape
set :- [ working in mm ]
Depth 10.0
feedrate 250.0
passdepth 5.0
plunge 100.0
Rapid hight 3.0
spindle 2000.0
start depth 0.0
tool 11
Post code and x3beam.tap is generated. Close LC and go to Mach3
this is the first part of the code. Mach3 barfs on line 45 no feed rate ?
Note rapid hight is 0.1 and depth is 0.0 ?
Just noticed only one feed has been applied where it specifies two 100 and 250.
N5 (File x3 beam )
N10 (File Posted in Mill Mode)
N15 (Monday, August 14, 2006)
N20 G90G80G40 G91.1
N25 G0 Z0.0000
N30 X13.6513 Y-23.4014
N35 M3 S0
N40 Z0.1000
N45 G1 Z0.0000 F0.00
G42
N50 G2 X16.8483 Y-21.7991 I1.1969 J1.6023
N55 G40
N60 X13.6513 Y-23.4014 I-2.0000 J0.0000
N65 G0 X26.0223 Y-15.7130
N70 Z0.1000
N75 G1 Z0.0000
N80 G2 X32.9738 Y-14.6854 I15.7479 J-82.5040
N85 X34.9006 Y-17.6993 I0.2095 J-1.9890
N90 G3 X33.7918 Y-22.3856 I6.8696 J-4.0998
N95 G2 X31.4550 Y-24.5028 I-1.9946 J-0.1466
N100 G3 X20.4959 Y-23.9733 I-7.6099 J-43.8283
N105 G2 X18.3464 Y-21.9136 I-0.1506 J1.9943
N110 G1 X17.9478 Y-20.1734
N115 G2 X19.1810 Y-17.3181 I1.7711 J0.9290
N120 G40
N125 X26.0223 Y-15.7130 I22.5892 J-80.8990
N130 G0 X39.3764 Y-25.0037
N135 Z0.1000
N140 G1 Z0.0000
N145 G2 X45.7702 Y-21.7991 I2.3938 J3.2046
N150 G40
N155 X39.3764 Y-25.0037 I-4.0000 J0.0000
N160 G0 X37.8802 Y-27.0066
N165 Z0.1000
N170 G1 Z0.0000
N175 G2 X48.2702 Y-21.7991 I3.8900 J5.2075
N180 G40
N185 X37.8802 Y-27.0066 I-6.5000 J0.0000
N190 G0 X57.5182 Y-15.7130
N195 Z0.1000
N200 G1 Z0.0000
-
Cool I will work on that tomorrow :)
Thank you
Brian
-
Hi, Brian
In the file below the G81 code is missing M3's before the M5's 4 places, this was done in plasma mode with 0.0.1.1.20,1 in plasma window.
N1 (File test55Dotpolyline )
N2 (File Posted in Plasma Mode)
N3 (Monday, August 14, 2006)
N4 G90 G80 G40 G91.1
N5 G0 Z0.0000
N6 G0 X0.0000 Y0.5020
N7 G0 Z0.0000
N8 M3 S0(PLasma On)
N9 G1 Y1.0040
N10 X1.0000
N11 Y0.0000
N12 X0.0000
N13 Y0.5020
N14 M5 (Plasma Off)
N15 G0 Z0.0000
N16 G0 X1.6996 Y1.6058
N17 G0 Z0.0000
N18 M3 S0(PLasma On)
N19 G2 X2.5020 Y2.0080 I0.3004 J0.4022
N20 X1.6996 Y1.6058 I-0.5020 J0.0000
N21 M5 (Plasma Off)
N22 G0 Z0.0000
N23 G0 X3.0000 Y1.0040
N24 G0 Z0.0000
N25 M3 S0(PLasma On)
N26 G1 X4.0000 Y2.0080
N27 Y0.0000
N28 X2.0000
N29 X3.0000 Y1.0040
N30 M5 (Plasma Off)
N31 G0 Z0.0000
N32 G0 X3.0000 Y1.2500
N33 G0 Z0.0000
N34 M3 S0(PLasma On)
N35 G81 X3.0000 Y1.2500 Z0.0000 R0.0000 F11.00
N36 M5 (Plasma Off)
N37 X3.7500 Y2.0000
M3;--------------------------------------------------M3 missing
N38 M5 (Plasma Off)
N39 Y2.7500
M3;--------------------------------------------------M3 missing
N40 M5 (Plasma Off)
N41 X0.2500
M3;--------------------------------------------------M3 missing
N42 M5 (Plasma Off)
N43 Y1.5000
M3;--------------------------------------------------M3 missing
N44 M5 (Plasma Off)
N45 G80
N46 G0 Z0.0000
N47 G0 X4.0000 Y2.2500
N48 G0 Z0.0000
N49 M3 S0(PLasma On)
N50 G1 Y2.7500 F111.00
N51 G3 X3.7500 Y3.0000 I-0.2500 J0.0000
N52 G1 X0.2500
N53 G3 X0.0000 Y2.7500 I-0.0000 J-0.2500
N54 G1 Y1.5000
N55 G3 X0.2500 Y1.2500 I0.2500 J-0.0000
N56 G1 X2.7500
N57 M5 (Plasma Off)
N58 Z0.0000
N59 M5 M9
N60 X0.0 Y0.0
N61 G40 G80M30
Thank's Chip
-
Brian,
Reading my code again there is no G21 or any way to select it and it hasn't selected a tool.
John S.
-
Okay,
Chip and John I should have time to get that all working tonight. I worked with Art last night with Art on the multiaxis probing :) So i will stop working on the toys and get back to work :'(
I am off Thursday (from work) so I better have it fixed this weekend!
-
The depth needs to be set to a negitive number :) I needed to add Positive cut heights for an OEM :(
Looking at the other stuff now :)
-
If you hava a negitive depth it seems to be working well..
Chip i am now off to see what I can do to get you fixed :)
-
Chip I am going to change the post so you can cut points. You will not be able to use the can cycle because I don't think you can have M3's and M5's in a can cycle :(
I should have this fixed in a few
-
Other then the power going out for a bit this was fun ot fix :) The new Post processor is making it SO much faster to make changes with out beaking other things in the program.. I changed the default post in Lcam but I know you are not running a plasma so you can change the post to make your water jet run :o If you have trouble I will give you a hand
Brian
-
There is also a new rev on the FTP server
:)
Please have a look and see if that fixes your trouble.. If you geys are happy I will start to finisha few other things that I am working on...
Thank you
Brian
-
Hi, Brian
There few items that still exist ill post them separately Ver.2.61.
If I load a DXF file and enter a Final Depth or a Rapid Hight without changing the Per Pass value upon clicking OK, LasyCam will lockup.
If I load a dxf file and set the Per Pass value to .5, then I can set Final Depth and Start Depth without lockup.
At this point I can change the Per Pass back to Default Value of 1 and have no lockup problem.
This is without closing LC and restarting, once shutdown and restarted it will freeze again with out changing the value in Per Pass if Final Depth or Rapid Hight are used.
If I change Per Pass to .5 close the window then change it back to 1 default value again then the problem is gone till restart of LC again.
If there are multipal layers then Per Pas value has to be changed in all layers
Windows End Task will shut LC down after freeze .
Thank's Chip
-
Hi Brian
The Dot/ Peirce is working now but there are some M5 missing now that were there before see below.
Also the first M3 has a S0 generates a error VB Editor Window.
N1 (File test55Dotpolyline )
N2 (File Posted in Plasma Mode)
N3 (Thursday, August 17, 2006)
N4 G90 G80 G40 G91.1
N5 G0 Z0.0000
N6 G0 X0.0000 Y0.5020
N7 G0 Z0.0000
N8 Z0.0000
N9 M3 S0(PLasma On);--------the S0 generates error, shoudent be there in plasma Mode
N10 G4 P1.0000
N11 G1 Y1.0040 F111.00
N12 X1.0000
N13 Y0.0000
N14 X0.0000
N15 Y0.5020
N16 G4 P1.0000
M5;--------------------------------------------------------------missing now
N17 G0 Z0.0000
N18 G0 X1.6996 Y1.6058
N19 G0 Z0.0000
N20 Z0.0000
N21 M3 S0(PLasma On)
N22 G4 P1.0000
N23 G2 X2.5020 Y2.0080 I0.3004 J0.4022
N24 X1.6996 Y1.6058 I-0.5020 J0.0000
N25 G4 P1.0000
M5---------------------------------------------------------------missing now
N26 G0 Z0.0000
N27 G0 X3.0000 Y1.0040
N28 G0 Z0.0000
N29 Z0.0000
N30 M3 S0(PLasma On)
N31 G4 P1.0000
N32 G1 X4.0000 Y2.0080
N33 Y0.0000
N34 X2.0000
N35 X3.0000 Y1.0040
N36 G4 P1.0000
M5;-------------------------------------------------------------missing now
N37 G0 Z0.0000
N38 G0 X3.0000 Y1.2500
N39 G0 Z0.0000
N40 Z0.0000
N41 M3 S0(PLasma On)
N42 G4 P1.0000
N43 G1 Z0.0000 F11.00
N44 G4 P1.0000
N45 M5(Plasma Off)
N46 G0 Z0.0000
N47 G4 P1.0000
N48 G0 X3.7500 Y2.0000
N49 Z0.0000
N50 M3(PLasma On)
N51 G4 P1.0000
N52 G1 Z0.0000 F11.00
N53 G4 P1.0000
N54 M5(Plasma Off)
N55 G0 Z0.0000
N56 G4 P1.0000
N57 G0 X3.7500 Y2.7500
N58 Z0.0000
N59 M3(PLasma On)
N60 G4 P1.0000
N61 G1 Z0.0000 F11.00
N62 G4 P1.0000
N63 M5(Plasma Off)
N64 G0 Z0.0000
N65 G4 P1.0000
N66 G0 X0.2500 Y2.7500
N67 Z0.0000
N68 M3(PLasma On)
N69 G4 P1.0000
N70 G1 Z0.0000 F11.00
N71 G4 P1.0000
N72 M5(Plasma Off)
N73 G0 Z0.0000
N74 G4 P1.0000
N75 G0 X0.2500 Y1.5000
N76 Z0.0000
N77 M3(PLasma On)
N78 G4 P1.0000
N79 G1 Z0.0000 F11.00
N80 G4 P1.0000
N81 M5(Plasma Off)
N82 G0 Z0.0000
N83 G4 P1.0000
N84 G0 Z0.0000
N85 G0 X4.0000 Y2.2500
N86 G0 Z0.0000
N87 Z0.0000
N88 M3 S0(PLasma On)
N89 G4 P1.0000
N90 G1 Y2.7500 F111.00
N91 G3 X3.7500 Y3.0000 I-0.2500 J0.0000
N92 G1 X0.2500
N93 G3 X0.0000 Y2.7500 I-0.0000 J-0.2500
N94 G1 Y1.5000
N95 G3 X0.2500 Y1.2500 I0.2500 J-0.0000
N96 G1 X2.7500
N97 G4 P1.0000
M5;-------------------------------------------------------------needs to be added for plasma
N98 Z0.0000
N99 M5 M9
N100 X0.0 Y0.0
N101 G40 G80M30
Thank's Chip
-
Could you see if you can edit the plasma post to get it to work the way you would like? This will help me with the post :)
-
Hi, Brian
Just read your last post that's what I am dooing now,------ Please read this post though.
The G81 caned cycle was something LC 2.60 chose not me, I figured you were going to pull a rabbit out of your hat.
The -1 worked one time for me, If I change the default Value in Per Pass from 1 to .5 then OK, then set Per Pass back to 1 then I can enter - or + in Final Depth and or Rapid Hight without LasyCam locking UP.
This is needed in all layers to keep it from locking up if Final Depth and or Rapid Hight are changed layer by layer.
Could it be when LC loads that the Default 1 value is-sent being properly loaded in some sort of Variable location ?.
Could you make the Gcode post also show Default Post / Plasma or User post"Plasma***.PST is being used at top of file.
Thank's for the plasma example.PST it's a little clearer where your going with this, Just allot of soreting this out for me and allot of cleaning up the code to remove previous structure to streamline for you.
On other item, LC saves my changes in the LC.XML But Never reloads any of them on startup, write now I am only using one file for testing.
Everything is in Mach3 in propper Sub. Dir's.
Thank's Chip
-
It is fixed :)
-
Hello Chip,
Are you telling me that Lcam is locking up when you enter the final depth? If it is I don't understand the steps :(
You can add the name of the post in the .pst file :) This is what I have been doing when I build them... I will add them to the default post in Mach3
I don't understand why Lcam is not loading your XML.. This has not been a problem for me :(
-
hi Brian, i have installed lazy cam ver 2.52, i not find the version 2.60
help me please ?
tank you
Franco
-
It is on the FTP server :)
This version with a few other fixes should be out tonight in the release
-
It is now in the new version on line :) Art just got the probe work that he was working on done so you have a new probe plugin and the new Lcam !
-
all ok
tank
Franco
-
Hi, Brian
Just downloaded the new Mach3d1.90.074, My default LC.XML loads now and the Plasma/DXF file that I use for tests is write and on the mark/Perfect !!!!!!!!!!!!! Whoo-Hoooooooo.
This is with plasma Post Options set to 0,0,1,1,20,1 works great.
Even though the LC.XML saves now, IF I don't Set the Per Pass to .5 along with Final Depth and Rapid Hight set to some value other than 0, it won't save the Per Pass and often frezze up LC if 0 is entered in Per Pass..
If you use Default setting's .3,.15,1,1.20,1 there are some issues. see below.
Just what I think below, maybe some one could comment on this.
The G0 should pickup the Plasma Initial Hight in plasma setting's window.
Need to add a Z0 after G0 X0 Y0 line # N114 to ret to start Pos.
N1 (File test55Dotpolyline )
N2 (Default Plasma Post)
N3 (File Posted in Plasma Mode)
N4 (Friday, August 18, 2006)
N5 G90 G80 G40 G91.1
N6 G0 Z0.3000;-----------------------Should be .3000 not 0.0000
N7 G0 X0.0000 Y0.5020
N8 G0 Z0.3000
N9 Z0.3000
N10 M3 S0(PLasma On)
N11 G4 P1.0000
N12 G1 Z0.1500 F11.00
N13 Y1.0040 F111.00
N14 X1.0000
N15 Y0.0000
N16 X0.0000
N17 Y0.5020
N18 G4 P1.0000
N19 M5 (Plasma Off)
N20 G0 Z0.3000;----------------------Should be .3000 not 0.0000
N21 G0 X1.6996 Y1.6058
N22 G0 Z0.3000
N23 Z0.3000
N24 M3 S0(PLasma On)
N25 G4 P1.0000
N26 G1 Z0.1500 F11.00
N27 G2 X2.5020 Y2.0080 I0.3004 J0.4022 F111.00
N28 X1.6996 Y1.6058 I-0.5020 J0.0000
N29 G4 P1.0000
N30 M5 (Plasma Off)
N31 G0 Z0.3000;-----------------------Should be .3000 not 0.0000
N32 G0 X3.0000 Y1.0040
N33 G0 Z0.3000
N34 Z0.3000
N35 M3 S0(PLasma On)
N36 G4 P1.0000
N37 G1 Z0.1500 F11.00
N38 X4.0000 Y2.0080 F111.00
N39 Y0.0000
N40 X2.0000
N41 X3.0000 Y1.0040
N42 G4 P1.0000
N43 M5 (Plasma Off)
N44 G0 Z0.3000;--------------------------Should be .3000 not 0.0000
N45 G0 X3.0000 Y1.2500
N46 G0 Z0.0000;---------------------------Should be .3000 not 0.0000
N47 Z0.3000
N48 M3 S0(PLasma On)
N49 G4 P1.0000
N50 G1 Z0.1500 F11.00
N51 G4 P1.0000
N52 M5(Plasma Off)
N53 G0 Z0.3000;---------------------------Should be .3000 not 0.0000
N54 G4 P1.0000
N55 M5 (Plasma Off)
N56 G0 X3.7500 Y2.0000
N57 Z0.3000
N58 M3(PLasma On)
N59 G4 P1.0000
N60 G1 Z0.1500 F11.00
N61 G4 P1.0000
N62 M5(Plasma Off)
N63 G0 Z0.3000;----------------------------Should be .3000 not 0.0000
N64 G4 P1.0000
N65 M5 (Plasma Off)
N66 G0 X3.7500 Y2.7500
N67 Z0.3000
N68 M3(PLasma On)
N69 G4 P1.0000
N70 G1 Z0.1500 F11.00
N71 G4 P1.0000
N72 M5(Plasma Off)
N73 G0 Z0.3000;-----------------------------Should be .3000 not 0.0000
N74 G4 P1.0000
N75 M5 (Plasma Off)
N76 G0 X0.2500 Y2.7500
N77 Z0.3000
N78 M3(PLasma On)
N79 G4 P1.0000
N80 G1 Z0.1500 F11.00
N81 G4 P1.0000
N82 M5(Plasma Off)
N83 G0 Z0.3000;------------------------------Should be .3000 not 0.0000
N84 G4 P1.0000
N85 M5 (Plasma Off)
N86 G0 X0.2500 Y1.5000
N87 Z0.3000
N88 M3(PLasma On)
N89 G4 P1.0000
N90 G1 Z0.1500 F11.00
N91 G4 P1.0000
N92 M5(Plasma Off)
N93 G0 Z0.3000;------------------------------Should be .3000 not 0.0000
N94 G4 P1.0000
N95 M5 (Plasma Off)
N96 G0 Z0.3000;-----------------------------Should be .3000 not 0.0000
N97 G0 X4.0000 Y2.2500
N98 G0 Z0.3000
N99 Z0.3000
N100 M3 S0(PLasma On)
N101 G4 P1.0000
N102 G1 Z0.1500
N103 Y2.7500 F111.00
N104 G3 X3.7500 Y3.0000 I-0.2500 J0.0000
N105 G1 X0.2500
N106 G3 X0.0000 Y2.7500 I-0.0000 J-0.2500
N107 G1 Y1.5000
N108 G3 X0.2500 Y1.2500 I0.2500 J-0.0000
N109 G1 X2.7500
N110 G4 P1.0000
N111 M5 (Plasma Off)
N112 Z0.3000;--------------------------------Should be .3000 not 0.0000
N113 M5 M9
N114 X0.0 Y0.0
Z0;--------------------------------------need's to be added
N115 G40 G80M30
Thank's for the Help, Chip
-
You need to change your rapid height to something other then 0.. If you set your rapid height to .3 I think you will be happy :)
That should do it..
-
Hi, Brian
Just want to Say This Rely Work's Nice Nice Nice, the .3 in Rapid Hight dose it.
If you set the Rapid to 2 the code thats generated produces a Rapid Hight of 2 to clear hold downs and also the .3 for Pierce Hight
from Plasma Window is present in the Gcode also.
If Layer Control Rapid Hight <= to Plasma Window Pierce Hight then Rapid Hight = Pierce Hight else leave Rapid Hight at Rapid Hight.
Then you wouldn't need to set Rapid Hight unless you wanted to generate hold down clearance level in Gcode.
There are a few extra Z .3000 generated though.
There are still some M3 with S0's generated that cause a lots of Problems with VB Script Editor from time to time, sometimes to the
point of Mach3 lock's up.
Have to use Win. Task Mgr, End Task Mach3 then run Driver Test to allow Mach3 to run again.
That sed, If your picking up the .3 and .15 from the plasma window for use in other spots to generat the Gcode.
Why not leave Rapid Hight for safe clearance level use.
Spent quit alot of time on this tonight, see code below
N1 (File test55Dotpolyline )
N2 (Default Plasma Post)
N3 (File Posted in Plasma Mode)
N4 (Saturday, August 19, 2006)
N5 G90 G80 G40 G91.1
N6 G0 Z2.0000
N7 G0 X0.0000 Y0.5020
N8 G0 Z0.3000
N9 ;----Z0.3000;----------------------------Extra Z.3000
N10 M3 ;----S0(PLasma On);--------------------------Del S0
N11 G4 P1.0000
N12 G1 Z0.1500 F11.00
N13 Y1.0040 F111.00
N14 X1.0000
N15 Y0.0000
N16 X0.0000
N17 Y0.5020
N18 G4 P1.0000
N19 M5 (Plasma Off)
N20 G0 Z2.0000
N21 G0 X1.6996 Y1.6058
N22 G0 Z0.3000
N23 Z0.3000;---------------------------Extra Z.3000
N24 M3 ;----S0(PLasma On);--------------------------Del S0
N25 G4 P1.0000
N26 G1 Z0.1500 F11.00
N27 G2 X2.5020 Y2.0080 I0.3004 J0.4022 F111.00
N28 X1.6996 Y1.6058 I-0.5020 J0.0000
N29 G4 P1.0000
N30 M5 (Plasma Off)
N31 G0 Z2.0000
N32 G0 X3.0000 Y1.0040
N33 G0 Z0.3000
N34 ;----Z0.3000;---------------------------Extra Z.3000
N35 M3 ;----S0(PLasma On);--------------------------Del S0
N36 G4 P1.0000
N37 G1 Z0.1500 F11.00
N38 X4.0000 Y2.0080 F111.00
N39 Y0.0000
N40 X2.0000
N41 X3.0000 Y1.0040
N42 G4 P1.0000
N43 M5 (Plasma Off)
N44 G0 Z2.0000
N45 G0 X3.0000 Y1.2500
N46 ;----G0 Z2.0000;--------------------Extra G0 Z2.0000
N47 Z0.3000
N48 M3 ;----S0(PLasma On);--------------------------Del S0
N49 G4 P1.0000
N50 G1 Z0.1500 F11.00
N51 G4 P1.0000
N52 M5(Plasma Off)
N53 G0 Z2.0000
N54 ;-------G4 P1.0000;------------------------Extra G4 P1
N55 ;-------M5 (Plasma Off);-------------------Extra M5
N56 G0 X3.7500 Y2.0000
N57 Z0.3000
N58 M3(PLasma On)
N59 G4 P1.0000
N60 G1 Z0.1500 F11.00
N61 G4 P1.0000
N62 M5(Plasma Off)
N63 G0 Z2.0000
N64 ;-----G4 P1.0000;-------------------------Extra G4 P1
N65 ;-----M5 (Plasma Off);--------------------Extra M5
N66 G0 X3.7500 Y2.7500
N67 Z0.3000
N68 M3(PLasma On)
N69 G4 P1.0000
N70 G1 Z0.1500 F11.00
N71 G4 P1.0000
N72 M5(Plasma Off)
N73 G0 Z2.0000
N74 ;----G4 P1.0000;-------------------------Extra G4 P1
N75 ;----M5 (Plasma Off);--------------------Extra M5
N76 G0 X0.2500 Y2.7500
N77 Z0.3000
N78 M3(PLasma On)
N79 G4 P1.0000
N80 G1 Z0.1500 F11.00
N81 G4 P1.0000
N82 M5(Plasma Off)
N83 G0 Z2.0000
N84 ;----G4 P1.0000;-------------------------Extra G4 P1
N85 ;----M5 (Plasma Off);--------------------Extra M5
N86 G0 X0.2500 Y1.5000
N87 Z0.3000
N88 M3(PLasma On)
N89 G4 P1.0000
N90 G1 Z0.1500 F11.00
N91 G4 P1.0000
N92 M5(Plasma Off)
N93 G0 Z2.0000
N94 ;----G4 P1.0000;-------------------------Extra G4 P1
N95 ;----M5 (Plasma Off);--------------------Extra M5
N96 ;----G0 Z2.0000;------------------------Extra G0 Z2000
N97 G0 X4.0000 Y2.2500
N98 G0 Z0.3000
N99 ;----Z0.3000;-------------------------Extra Z.3000
N100 M3 ;---S0(PLasma On);------------------------Del S0
N101 G4 P1.0000
N102 G1 Z0.1500
N103 Y2.7500 F111.00
N104 G3 X3.7500 Y3.0000 I-0.2500 J0.0000
N105 G1 X0.2500
N106 G3 X0.0000 Y2.7500 I-0.0000 J-0.2500
N107 G1 Y1.5000
N108 G3 X0.2500 Y1.2500 I0.2500 J-0.0000
N109 G1 X2.7500
N110 G4 P1.0000
N111 M5 (Plasma Off)
N112 Z2.0000
N113 M5 M9
N114 X0.0 Y0.0
N115 G40 G80M30
Thank's, Chip
-
Hi, Brian
My prev. post was done with the default post in LC couldn't get the Plasma example to work in ver.2.61.
Down loaded Mach3D1.90.075 with ver. 2.62 LC and posts, This Rely Works Nice.
The Plasma post, I can change and save them now. Just made one change hear this is nice.
Thank's for all the Help, Chip