Messages

1171

Mach4 General Discussion / Re: DRO Code differences

« on: April 25, 2014, 12:06:39 AM »

The X position is the user coordinates only.  It will not toggle between machine, user, and distance to go like X Multi Pos will.

Steve

1172

Mach4 General Discussion / Re: Comments about Mach4 in Demo

« on: April 24, 2014, 11:17:21 PM »

When will we get a LPT plugin to use ??

(;-) TP

There might not be one.  Not decided yet.

Steve

1173

Mach4 General Discussion / Re: Comments about Mach4 in Demo

« on: April 24, 2014, 09:30:29 PM »

Pan the tool path with both mouse buttons.

Other hints:
Left double click orients the path in the top down view.
Right double click orients the path in the ISO view.

Steve

1174

Mach4 General Discussion / Re: Comments about Mach4 in Demo

« on: April 24, 2014, 02:10:17 PM »

LOL!!!  You don't know how many times I have said I would fix that date!!!  I'm going to do it NOW! 

1175

Mach4 General Discussion / Re: Comments about Mach4 in Demo

« on: April 23, 2014, 11:50:23 PM »

Alt-Enter executes the MDI from the keyboard.  Since it is multi-line, alt-UP and alt-down cycle through the previous commands.

Keyboad control is via a plugin that has not been released.  Just mouse around for a bit until we release the keyboard stuff.

Steve

1176

Galil / Re: Old Dynapath System 10 upgrading to Galil CS 18420 ICM 2900 No idea on wiring???

« on: April 18, 2014, 01:25:37 PM »

Hmm...  Are you able to run the Galil with the Terminal.  Meaning do you get encoder counts in the watch window?

You do not have to setup the Mach encoders for the Galil, so that isn't it.  They should be fed to Mach by the plugin.

Steve

1177

Galil / Re: Old Dynapath System 10 upgrading to Galil CS 18420 ICM 2900 No idea on wiring???

« on: April 17, 2014, 06:17:05 PM »

By balance, you mean not drift?  If so, you can use the OF command on the Galil to correct.  And I believe there is a pot on the amp that can adjust that to.  And the point become moot once the servos are energized and the Galil is holding them in position.

Steve

1178

Galil / Re: Limit switch problem

« on: April 17, 2014, 06:12:35 PM »

BTW, there is/was a pretty good explanation of this in a thread on this forum somewhere.  Finding it is the problem.

Steve

1179

Galil / Re: Limit switch problem

« on: April 17, 2014, 06:11:40 PM »

It is not you that is confused!  What you said is correct.  You can test this in the Galil terminal and using the watch window.  If LSCOM is positive, the data record will show one way with a NC switch as opposed to when LSCOM is negative.  I can't remember which way it goes at the moment, so you will just have to test and see.

Look at the limit in the watch window when you have it wired LSCOM to +12v and hook a NC switch up to it.  If limit switch is 1, then CN needs to be configure accordingly.  CN is configured with the limits active low check box in the plugin.  Because when the switch is depressed, the limit switch value in the watch window should go to 0.  And vice verse.  Once this is set so the Galil sees what you want, then you may have to reverse the polarity of the signal for that limit switch in Ports and Pins.  Negate is what it is called, I believe.  At some point, you will get both Mach and the Galil to agree on the switch configuration.

Steve

1180

Galil / Re: Old Dynapath System 10 upgrading to Galil CS 18420 ICM 2900 No idea on wiring???

« on: April 16, 2014, 10:45:04 PM »

http://www.ormec.com/LinkClick.aspx?fileticket=upw7DE2FD8A%3D&tabid=168&mid=757

That is the manual for your drives.  It looks like you may need to wire the limits in parallel with the Galil. 

Steve