Messages

21

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 19, 2014, 09:25:54 AM »

can put the parameter in CS-MIO   that fault is activated as LOW   .... and do that 

22

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 18, 2014, 04:46:54 PM »

look the second picture   when was the fault (ALM) it activate just a transistor

23

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 18, 2014, 12:02:07 PM »

is that ok ? how i connect the faults outputs

24

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 18, 2014, 11:36:59 AM »

if you see your picture with connection PNOZ .... only one wire from drivers go to Pnoz   ....  i my situation can i connect  4 faults in the same input of PNOZ

25

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 18, 2014, 10:34:42 AM »

ok I recommend not using the PNOZ ?

26

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 16, 2014, 05:35:46 PM »

hi in your picture  de fault from driver 1  .... where it go .... i have not ( input auxiliary alarm  for the second driver )

27

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 11, 2014, 06:36:32 PM »

hi hood

yes i do exactly that  .... but when push the button ESTOP   and after the ST1    ... my controllers stay in alarm ... how to activate normal mode .

28

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 08, 2014, 12:29:38 PM »

hi Hood

I think you can help me ?

this is my driver  : http://www.automationsystemsandcontrols.net.au/PDF's%20Mitsubishi/Manuals/SERVO/MR-J2S-_A%20Instruction%20Manual.pdf

Thanks

29

CS-Lab / Re: how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 07, 2014, 02:59:55 PM »

or do i need to use PNOZ with my drivers

30

CS-Lab / how to wire PNOZ X7 with drivers MR-J2S-60A and CSMIO-IP-A

« on: April 06, 2014, 01:29:40 PM »

Hi

I need to help  how to wire correctly the PNOZ x7  to my driver MR-J2S.

http://www.cs-lab.eu/en/upload/pdf/User_Manual_CSMIOIPA_EN.pdf    (page : 11)

https://fr3a.mitsubishielectric.com/fa/fr/service/download/sendfile?id=1375&type=doc_loc&saveAs=0&form_submit=Afficher+maintenant       (page: 3-6)

Thanks